manualshive.com logo in svg

Chrysler Pacifica Hybrid 2018, Owner'S Manual, Page: 52 / 617

Share
Download
Chrysler Pacifica Hybrid 2018 Owner'S Manual Download Page 52

The message will stay active until the ignition is placed in
the ON/RUN position.

How To Use Remote Start

All of the following conditions must be met before the
vehicle will remote start:

•

Gear Selector in PARK

•

Doors closed

•

Hood closed

•

Liftgate closed

•

Hazard switch off

•

Brake switch inactive (brake pedal not pushed)

•

Battery at an acceptable charge level

•

Key fob PANIC button not pushed

•

System not disabled from previous remote start event

•

Vehicle alarm system indicator flashing

•

Ignition in STOP/OFF position

•

Fuel level meets minimum requirement

•

MIL lamp is OFF, Vehicle is in propulsion system active

WARNING!

•

Do not start or run an engine in a closed garage or
confined area. Exhaust gas contains Carbon Monox-
ide (CO) which is odorless and colorless. Carbon
Monoxide is poisonous and can cause serious injury
or death when inhaled.

•

Keep key fobs away from children. Operation of the
Remote Start System, windows, door locks or other
controls could cause serious injury or death.

To Enter Remote Start Mode

Push and release the Remote Start button on the key fob
twice within five seconds. The vehicle doors will lock, the
turn signals will flash twice, and the horn will chirp twice.
Then the vehicle will start, and the vehicle will remain in
the Remote Start mode for a 15-minute cycle.

NOTE:

•

The vehicle can be started two consecutive times (two
15-minute cycles) from the key fob. However, the igni-
tion must be placed in the ON/RUN position before you
can repeat the start sequence for a third cycle.

50

GETTING TO KNOW YOUR VEHICLE

Summary of Contents for Pacifica Hybrid 2018










































































































































































































































































































































































































































































































































































































































Reviews:

No comments