Chrysler Pacifica Hybrid 2018 Owner'S Manual Download Page 30

Page: 30 / 617

Portable EVSE Cordset Fault Code List

Flashing

Fault
Code

Flashing

Indicator

Fault Indication

Recommended Actions

1, 1, 1, 2

Fault

Portable EVSE Cordset

Internal Fault

Unplug the Portable EVSE Cordset from the vehicle charge inlet

and retry to charge. If the issue is not corrected, check the Por-

table EVSE Cordset and Vehicle at a service location.

1, 2, 2, 1

AC Power

Outlet Wiring Bad

Ground

Attempt to charge the vehicle at a different outlet. Contact a

certified electrician to check the electrical outlet and AC Supply

(house wiring).

1, 2, 1, 1

Fault

Portable EVSE Cordset

Internal Fault

Check Portable EVSE Cordset and Vehicle at a service location.

1, 2, 1, 2

Fault

CCID Leakage Current

Detected

Disconnect charge connector and retry charging. If problem per-

sists, check the Portable EVSE Cordset and Vehicle at a service

location.

2, 2, 2, 1

Fault

Vehicle Interface Con-

nector

Error with the Vehicle Charge Connector Interface — Check for

water or other contamination in the vehicle charge inlet or

charge connector.

2, 2, 2, 2

Fault

Vehicle Interface Con-

nector

Error with the Vehicle Charge Connector Interface — Check for

water or other contamination in the vehicle charge inlet or

charge connector

GETTING TO KNOW YOUR VEHICLE

Summary of Contents for Pacifica Hybrid 2018










































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Pacifica Hybrid 2018

Reviews:

Chrysler Pacifica Hybrid 2018, Owner'S Manual, Page: 30 / 617

Search results

Summary of Contents for Pacifica Hybrid 2018

Reviews: