manualshive.com logo in svg

Chrysler Pacifica Hybrid 2018, Owner'S Manual, Page: 167 / 617

Share
Download
Chrysler Pacifica Hybrid 2018 Owner'S Manual Download Page 167

engine will run whenever the vehicle is operational (no
electric only operation) until the low fuel level warning is
activated. It is possible to exit the Fuel and Oil Refresh
Mode sooner by adding new fuel to the vehicle’s fuel tank.

NOTE:

Fuel Freshness is recalculated whenever fuel is

added to the vehicle’s fuel tank.

KeySense Cluster Messages — If Equipped

When the KeySense key is in use there will be:

•

Continuous, dedicated telltale

•

Unique Display Splash Screen

With KeySense in use there will be multiple

associated messages shown in the following table:

Setting

Instrument Cluster Display Message

None – With vehicle ignition

ON

“KeySense in use. Max vehicle speed set to xx MPH/or km/h”

Max Vehicle Speed

•

“Max speed reached. KeySense in use” supported by a chime

•

“Approaching max speed xx MPH/km” supported by a chime

Start Up Fuel Alert message

“Range to empty xxx miles or km”

Early Low Fuel Alert Message

“Fuel Low”

ParkSense

“Feature cannot be disabled. KeySense in use”

Blind Spot

“Feature cannot be disabled. KeySense in use”

Forward Collision Warning

“Feature cannot be disabled. KeySense in use”

4

GETTING TO KNOW YOUR INSTRUMENT PANEL

165

Summary of Contents for Pacifica Hybrid 2018










































































































































































































































































































































































































































































































































































































































Reviews:

No comments