Cardin SLi Series Instruction Manual Download

Page: 7 / 16

• This device has been created to be integrated into the structure of specially made

sliding gates. The geared motor is fitted with screw type attachments that allow
it to be fitted inside metal profiles.

ASSEMBLY PROCEDURE

The unit may be positioned either to the right or to the left of the passageway.
Respect the following limits:
-

SLi724

: max. weight

700 kg

SLi1024

: max. weight

1000 kg

SLi24DRACO

: max. weight

1000 kg

The builder must make sure that the closing system respects the technical
indications supplied by the standards and laws in force:
-  Opening and closing direction mechanical stops;
-  Safety devices;
-  Correct risk analysis at possible crushing points etc.
See:

www.cardin.it - archives - Installation guide and approvals certificates -

MAINTENANCE

ELECTRICAL CONNECTION

Important remarks

• After having installed the device,

and before powering up the

programmer

, release the door (manual release mechanism)

and move it manually, checking that it moves smoothly and
has no unusual points of resistance.

• The presence of the electrical current sensor does not dispense

with the obligation to install photoelectric cells and other
safety devices foreseen by the safety standards in force.•
Before connecting the appliance make sure that the voltage
and frequency rated on the data plate conform to those of the
mains supply.

• The motor’s power cable must be made of polychloroprene in

conformity with the international standard

60245 IEC 57

(e.g.

3 x 1.5 mm

H05RN-F).

• The cable may only be replaced by qualified technicians.
• An all pole trip switch with at least

3 mm

between the contacts

must be installed between the unit and the mains supply.

• Don’t use cables with aluminium conductors; don’t solder the

ends of cables which are to be inserted into the binding posts;
use cables marked

T min 85°C

and resistant to atmospheric

agents.

• The terminal wires must be positioned in such a way that both

the wire and the insulating sheath are tightly fastened.

Motor - encoder and terminal board connections

• You must scrupulously respect the motor connection sequence between

the motors and the programmer. The order of the binding post connections
1 to 7 is identical on both;

- connect the wires of motor, the encoder and the

release mechanism (binding post 7 ‘

’ orange

for

SLi24DRACO

and ‘

’ white for

SLi724 /

SLi1024

) to the main board of the electronic

programmer using the terminal block;

- connect the pre-wired terminal to the motor

terminal block.

Electronic programming unit

Instructions for programming the ECU and battery powered operation
can be found in the

MULTI-ECU SOFTWARE

manual

ZVL608

supplied

with the automation.

To use the

24 month

50000 manoeuvre

guarantee, read the following

notes carefully.

Attention!

Before carrying out any cleaning or maintenance operations

make sure the power is disconnected at the mains, the motor power
cables are disconnected and the batteries have been disconnected.
Eventual repair work must be carried out by specialised personnel
using original spare parts.
The motor does not normally require particular maintenance; in any
case the

24 month

50000 manoeuvre

guarantee is only valid if the

following controls have been observed and eventual maintenance has
been carried out to the machine ‘sliding gate’:
- check the straightness of the toothed rack, make sure the teeth fit

correctly in the pinion throughout its entire length; in particular the gear
rack must have a cross section of

20 x 20 mm

;

- check the play of the gear rack - pinion (

1-2 mm

);

- periodically check the moving parts for wear and tear and grease if

required, using lubricants which maintain their friction levels unaltered
throughout time and are suitable for temperatures of

-20 to +70°C

;

- check the battery charge level.
These checks must be written down as they are paramount in validating
the guarantee.

INSTRUCTIONS FOR USE