Car-O-Liner Quick 42 Instruction Manual Download Page 16

Page: 16 / 113

Car-O-Liner Group AB

Quick 42

40724, EN- rev. 8, 2017-09

2.3 Safety

signs

Undamaged safety signs shall always be affixed at the indicated places (

see

section 2.3.1 "Placement of safety signs"

). If any signs are damaged or miss-

ing, the user is responsible for their immediate replacement. The following
safety signs can be found on the equipment:

PROHIBITED

For personnel to be on the lift while it is moving.

WARNING

The highest allowed vehicle weight is 3 000 kg (6 600 lbs).

WARNING

Minimum allowed distance between axle and bench end is 0.5 meter when
lifting a vehicle with short wheel-base (1.5-2 meter). Otherwise there is risk
for crushing injuries.

WARNING

During inspection and maintenance with the lift unit in the raised position,
the lift unit must be blocked against unintentional lowering.

WARNING

Danger of tripping due to loose hoses, etc.

WARNING

The draw aligner is to be equipped with a hydraulic cylinder with a maxi-
mum capacity of 10 tons (300 bar).

WARNING

Watch out for flying objects during aligning work. Do not stand behind or
near the draw aligner during a pull.

Part No 44307 (kit)

Part No 41642 (kit)

Part No 44307 (kit)

Part No 35721 (kit)

Summary of Contents for Quick 42


















































































































Search results

Summary of Contents for Quick 42

Reviews:

Brands by name

Popular brands

Car-O-Liner Quick 42, Instruction Manual

Search results

Summary of Contents for Quick 42

Reviews:

Brands by name

Popular brands