Canon Colorado M Series Operation Manual Download Page 371 | Manualshive

Page: 371 / 378

background image

End of Life; Handling of disposal of parts (Japan)

Translation: Handling of disposals. Used consumables and expendables must be discarded by the
customer as industrial waste in accordance with the laws as well the regulations of local
government.

RoHS (Vietnam)

Products sold in Vietnam market comply with following Circular and Decision - "Circular No.
30/1011/TT-BCT dated August 10, 2011 of the Ministry of Industry and Trade stipulating
temporarily the permissible content limitation of some toxic chemicals in the electronic, electrical
products" - Decision No.4693/QD-BCT correcting Circular 30/2011/TT-BCT.

For the statement on Canon Marketing Vietnam website, please see the last paragraph on the
web page of the following URL:

http://www.canon.com.vn/personal/web/company/about/

REACH compliance (EEA including Switzerland)

• REACH regulation (EC No 1907/2006) article 33 requires information to be communicated to

customers/end users about the presence of SVHC substances included in the REACH candidate
list when such substances are above the threshold of 0.1% in articles. If such information has
to be communicated it can be found on

https://www.canon-europe.com/sustainability/

.

Under normal conditions of use, there will be no exposure and no special measures are
required for safe use.

Computers (All countries)

• Regulation EU 617/2013 calls for the environmentally sound design of computers.This

information can be found at the support site of your product:

https://downloads.cpp.canon/

Acoustic noise emission (All countries)

• Sound pressure (LpA =

66 dB(A)

) is used to characterize the sound level that will be

experienced at operator position and is defined as the dynamic variation of the static pressure
of air measured in force per unit area. Sound pressure is normally represented in decibels [dB].
Typical values are a sound pressure level of 0 dB, which is the average threshold of human
hearing, and 60 to 70 dB for normal conversation, 110 dB at an extremely loud music concert,
and 150 dB for the noise of a jet engine at close range.

Recycled paper (All countries)

The use of recycled paper also benefits the environment. The Colorado M-series is designed to
use recycled paper, including chlorine free paper, which complies with the requirements of
EN12281:2002.

Chapter 10 - Regulation Notices

371

«
...
369
370
371
372
373
...
»

Summary of Contents for Colorado M Series



























































































































































































































































































































































































Reviews:

No comments

Related manuals for Colorado M Series

Brand: Octave Pages: 2

Brand: Lanier Pages: 265

Brand: Olivetti Pages: 20

Brand: Olivetti Pages: 63

Brand: Olivetti Pages: 180

Brand: Olivetti Pages: 118

Brand: Olivetti Pages: 80

Brand: Olivetti Pages: 253

Brand: Olivetti Pages: 163

d-COLOR MF222plus

Brand: Olivetti Pages: 151

Brand: Olivetti Pages: 176

Brand: Tally Pages: 53

T2265 SprintPro

Brand: Tally Pages: 30

Brand: Tally Pages: 108

Brand: TallyGenicom Pages: 2

Brand: TallyGenicom Pages: 2

Brand: Savin Pages: 160

DiMAGE Scan Elite 5400 II

Brand: Konica Minolta Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands