Canon Colorado M Series Operation Manual Download Page 304 | Manualshive

Page: 304 / 378

background image

• [Immediately]: The printer installs the operating system updates once they are present on

the system. The printer remains operational. To finalize the installation, you must restart
the system.

• [At specified time]: The printer installs the operating system updates at the time you

specify. The printer remains operational. To finalize the installation, you must restart the
system.

• [Manually]: You install operating system updates manually once they are present on the

system. The printer remains operational. To finalize the installation, you must restart the
system.

5. Select [Send email to system administrator about status of updates] to receive status

information about the installation process. System administrators who have a configured
email address receive these emails.
You receive an email when the following status has been reached:
• When you select [Manually] in the [Installation moment] setting, you receive an email

when operating system updates are available for installation and when you must restart
the system to finalize the installation.

• You receive an email when operating system updates are being installed.
• You receive an email when operating system updates have been installed.
• You receive an email when an error occurs during downloading or installation of the

software updates.

6. Click [OK].

Upload and install an operating system update from a file via the Settings Editor

1. Open the Settings Editor and go to: [Support]

→

[Software updates].

2. Go to [Operating system updates].
3. Check if the update is already installed: compare the "kb" number from the update with the

"kb" number of installed updates. If the update is already installed, do not install it again.

4. Click [Install from file].

Configure, upload and install operating system updates from a file

304

Chapter 9 - Troubleshooting and support

«
...
302
303
304
305
306
...
»

Summary of Contents for Colorado M Series



























































































































































































































































































































































































Reviews:

No comments

Related manuals for Colorado M Series

Brand: Xerox Pages: 11

Brand: Xerox Pages: 30

Versant 4100 Press

Brand: Xerox Pages: 68

Brand: Xerox Pages: 4

Brand: Xerox Pages: 4

Brand: Xerox Pages: 2

Versant 2100 Press

Brand: Xerox Pages: 68

imageRUNNER ADVANCE DX 6870i

Brand: Canon Pages: 115

imagerunner advance C5550i

Brand: Canon Pages: 1556

Brand: Ricoh Pages: 682

Brand: Konica Minolta Pages: 32

Brand: Tally Pages: 28

Brand: MIMAKI Pages: 2

Brand: Felix printers Pages: 26

ColorQube 87 Series

Brand: Xerox Pages: 32

WorkCentre Pro 416

Brand: Xerox Pages: 470

Brand: Tascam Pages: 2

Brand: DNP Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands