Canon 7086 Series, Service Manual

Page: 648 / 735

Chapter 17
17-60
DEV-SLOW Use it to enable/disable the developing cylinder speed variation mechanism.
1
settings
0: change to suit environment; 1: high speed; 2: low speed (default)
MEMO:
Do not use for servicing.
W/SCNR Use it to indicate the presence/absence of a reader unit.
1
settings
0: printer model (w/o reader); 1: copier model (w/ reader)
If the reader unit is detected at start-up, '1' will be set automatically.
STPL-SFT Use it to enable/disable offset stacking in stapler mode.
1
settings
0: use offset stacking in stapler mode (default)
1: do not use offset stacking in stapler mode
The foregoing choice is valid only when 1-point stapling is used.
DFDST-L1 Use it to adjust the dust detection level when the ADF is in use. (sheet-to-sheet correction)
1
A higher setting will make the mechanism more sensitive, detecting finer particles of dust.
settings: 0 to 255 [Default: 80]
DFDST-L2 Use it to adjust the dust detection level when the ADF is in use. (post-job detection)
1
A higher setting will make the mechanism more sensitive, detecting finer particles of dust.
settings: 0 to 255 [Default: 80]
CCD-LUT * Use it to indicate whether or not to use data for CCD gain correction.
1
Use it to correct the deterioration of the image due to aging (the density difference at the center joint area of the image).
Indicates whether or not to use the data collected by COPIER > FUNCTION > CCD > LUT-ADJ2.
settings
0: do not use [Default]; 1: use (1-point correction); 2: use (3-point correction)
ENVP-INT Use it to set the intervals at which the history data is collected on the machine inside temperature/fixing temperature.
1 settings: 0 to 480 (unit: min)
If '0', the history data is not collected.
BASE-SW Use it to switch from the MEAP full model to the base model.
1
Use it when trouble attributable to MEAP application occurs. By setting to '0', the operation of MEAP application can be controlled.
settings
0: off (base model); 1: on (full model) [Default]
MEMO:
The change only from '1' to '0' is possible.
SC-L-CNT Use it to set the threshold for identifying large size paper for the scan counter.
1
Settings
0: Count the paper larger than B4 as large size. (A paper that is B4 or smaller is considered as small size.) [Default]
1: Count the paper larger than LTR as large size. (A paper that is LTR or smaller is considered as small size.)
The scan counter threshold at copy is determined as follow depending on the combination with the setting value of B4-L-CNT
(COPIER > OPTION > USER > B4-L-CNT):
<In case SC-L-CNT, B4-L-CNT=(0, 0)>
Count the paper larger than B4 as large size. (A paper that is B4 or smaller is considered as small size.)
<In case SC-L-CNT, B4-L-CNT=(0, 1)>
Count the paper that is B4 or larger as large size. (A paper smaller than B4 is considered as small size.)
<In case SC-L-CNT, B4-L-CNT=(1, 0) or (1, 1)>
Count the paper larger than LTR as large size. (A paper that is LTR or smaller is considered as small size.)
LDAP-ADD Use it to indicate whether or not to add a LDAP search switch.
1
Indicates whether or not to add 'Object Class' and 'SrchNameRow' (Search Name Row) to the pull-down list showing the normal set
of conditions (name, group, organization unit, e-mail).
settings
0: do not add; 1: add
The addresses to be searched are limited to e-mail addresses.
COPIER > OPTION > BODY
*: model equipped with DADF-Q1 (outside Japan: iR7105/7095; inside Japan: All model).
**: model equipped with DADF-M1 (outside Japan: iR7086).
***: up graded version
Sub item Description Level