Canon 7086 Series, Service Manual

Page: 643 / 735

Chapter 17
17-55
17.5.2 FEEDER
17.5.2.1 FEEDER Items
0011-6095
iR7105 / iR7095 / iR7086
T-17-46
FEEDER > FUNCTION
*: model equipped with DADF-Q1 (outside Japan: iR7105/7095; inside Japan: All model).
**: model equipped with DADF-M1 (outside Japan: iR7086).
Sub item Description Level
SENS-INT Use it to adjust the sensitivity of the various sensors of the ADF.
1
Be sure to clean the sensors before executing the item.
Procedure
1) Select the item, and press the OK key.
2) See that the adjustment ends automatically.
BLT-CLN * Use it to clean the separation belt of the ADF.
1
<Procedure>
1) Select the time, and press the OK key.
2) See that the separation belt goes on. Press the Stop key to stop the operation.
REG-CLN * Use it to clean the registration roller of the ADF.
1
<Procedure>
1) Select the item, and press the OK key.
2) See that the registration roller rotates. Press the Stop key to stop the operation.
MTR-CHK ** Use it to check the ADF motor on its own.
1
<Procedure>
1) Select the item.
2) Type in the number of a specific part using the keypad.
3) Press the OK key.
4) Press MTR-ON to check the operation.
No. and Part
0: pickup motor
1: transport motor
TRY-A4 ** Use it to execute auto adjustment on paper width detection reference point 1 for the original pickup tray of the ADF. (A4) 1
TRY-A5R ** Use it to execute auto adjustment on paper width detection reference point 2 for the original pickup tray of the ADF. (A5R) 1
TRY-LTR ** Use it to execute auto adjustment on paper width detection reference point 1 for the original pickup tray of the ADF. (LTR) 1
TRY-LTRR
** Use it to execute auto adjustment on paper width detection reference point 2 for the original pickup tray of the ADF. (LTRR)
1
FEED-CHK
** Use it to check paper passage for the ADF on its own.
1
<Procedure>
1) Select the item.
2) Type in the number of a specific paper passage mode using the keypad.
3) Press the OK key.
4) Press FEED-ON to check the operation.
No. and Paper Passage Mode
0: simplexing pickup delivery operation
1: duplexing pickup delivery operation
2: simplexing pickup delivery operation w/ stamp
3: duplexing pickup delivery operation w/ stamp
CL-CHK ** Use it to check the ADF clutch on its own.
1
<Procedure>
1) Select the item
2) Type in the number of a specific part using the keypad.
3) Press the OK key.
4) Press CL-ON to check the operation.
No. and Part
0: pickup clutch
CL-ON ** Use it to start the operation of the clutch.
1
<Procedure>
1) Select the item, and press the OK to start the operation of the clutch.
2) Press the OK key to stop the operation. (It will stop automatically in about 2 sec. But the indication will not change to 'STOP' until
the OK key is pressed once again.)
FAN-CHK ** Use it to check the operation of the clutch on its own.
1
<Procedure>
1) Select the item.
2) Type in the number of a specific part using the keypad.
3) Press the OK key.
4) Press FAN-ON to check the operation.
No. and Part
0, 1: cooling fan
FAN-ON ** Use it to start fan operation.
1
<Procedure>
1) Select the item, and press the OK key to start fan operation.
2) Press the OK key to stop the operation. (The operation will stop automatically in about 5 sec, but the indication will not change to
'STOP' until the OK key is pressed once again.)