Canon 1730, Service Manual

Page: 240 / 358

7
7
7-6
7-6
Error Code > Error Code > Error Code Details
Error Code > Error Code > Error Code Details
Ecode
Detail
Code
Item Description
E247 0001 Title System error
Description System error
Remedy
Contact the service company office
E261 0000 Title Zero cross signal error
Description When the relay is ON, the zero cross signal failed to be detected for
500 msec or longer.
*When the same status was detected again after executing an error
retry.
Remedy 1. Check the connector connection. (All connectors on the DC Controller
PCB)
2. Replace the DC Controller PCB (PCB1).
E350 0000 Title System error
Description System error
Remedy
Contact the service company office
E350 0001 Title System error
Description System error
Remedy
Contact the service company office
E350 0002 Title System error
Description System error
Remedy
Contact the service company office
E350 0003 Title System error
Description System error
Remedy
Contact the service company office
E350 3000 Title System error
Description System error
Remedy
Contact the service company office
E354 0001 Title System error
Description System error
Remedy
Contact the service company office
E354 0002 Title System error
Description System error
Remedy
Contact the service company office
E355 0000 Title System error
Description System error
Remedy
Contact the service company office
E355 0004 Title System error
Description System error
Remedy
Contact the service company office
E355 0005 Title System error
Description System error
Remedy
Contact the service company office
Ecode
Detail
Code
Item Description
E530 8001 Title Front Alignment Motor (M4) error
Description At initialization of the Front Alignment Plate, the Front Alignment Plate
failed to move from the Front Alignment Plate HP Sensor (S4) although
the Front Alignment Motor (M4) was driven for 10 mm.
Remedy 1. Check the connector connection of the Front Alignment Plate HP
Sensor (S4) or the Front Alignment Motor (M4).
2. Check for open circuit of the Harness of the Front Alignment Plate HP
Sensor (S4) or the Front Alignment Motor (M4).
3. Replace the Front Alignment Plate HP Sensor (S4).
4. Replace the Front Alignment Motor (M4).
5. Replace the Finisher Controller PCB.
E530 8002 Title Front Alignment Motor (M4) error
Description At initialization of the Front Alignment Plate, the Front Alignment Plate
failed to be detected by the Front Alignment Plate HP Sensor (S4)
although the Front Alignment Motor (M4) was driven for 0.78 seconds.
Remedy 1. Check the connector connection of the Front Alignment Plate HP
Sensor (S4) or the Front Alignment Motor (M4).
2. Check for open circuit of the Harness of the Front Alignment Plate HP
Sensor (S4) or the Front Alignment Motor (M4).
3. Replace the Front Alignment Plate HP Sensor (S4).
4. Replace the Front Alignment Motor (M4).
5. Replace the Finisher Controller PCB.
E531 8001 Title Staple Motor (M9) error
Description The Stapler failed to move from the Staple HP Sensor (S11) within the
staple execution time (0.45sec).
Remedy 1. Check the connector connection of the Staple Unit.
2. Check for open circuit of the Harness of the Staple Unit.
3. Replace the Staple Unit.
4. Replace the Finisher Controller PCB.
E531 8002 Title Staple Motor (M9) error
Description After execution of staple operation, the motor was operated in the
positive direction, but the Staple Unit could not be detected by the
Staple HP Sensor (S11) within 0.46 seconds. Then, the motor was
rotated in the negative direction, but the Staple Unit could not be
detected by the Staple HP Sensor (S11) within 0.46sec.
Remedy 1. Check the connector connection of the Staple Unit.
2. Disconnect the Harness of the Staple Unit.
3. Replace the Staple Unit.
4. Replace the Finisher Controller PCB.