Can-Am 2009 DS 450 Operator'S Manual Download | Manualshive

Page: 71 / 152

background image

OPERATING INSTRUCTIONS

vmo2008-011-004_b

TYPICAL

Press and hold engine start button until
engine starts.

Release button immediately when en-
gine has started.

vmo2008-018-005_c

WARNING

Do not apply throttle while start-
ing.

Shifting the Transmission

Gearshift Control

This vehicle has five gears.

To shift the transmission, pull in the
clutch lever, then operate gearshift
pedal as follows.

WARNING

Always use the clutch lever to up-
shift or downshift.

One full stroke of the pedal shifts the
transmission to the next higher or low-
er gear in the shifting sequence. The
pedal should automatically return to its
original position.

To upshift to a higher gear, put the end
of your boot under gearshift lever and
lift up the pedal one full stroke.

To downshift, lean the tip of the
gearshift pedal and depress pedal one
full stroke.

To select neutral, place transmission in
1

st

gear then lift up pedal gently.

vmo2008-011-019_g

WARNING

Always release the throttle when
shifting gears. Shifting gears with-
out releasing the throttle, could
cause loss of control or cause the
vehicle to overturn.

NOTICE

Make sure parking brake

is fully disengaged before operating
vehicle.

Stopping the Engine

WARNING

Avoid parking vehicle on slope.

_____________________

69

«
...
69
70
71
72
73
...
»

Summary of Contents for 2009 DS 450

























































































































































Reviews:

No comments

Related manuals for 2009 DS 450

Brand: Yerf-Dog Pages: 22

Brand: Landa Pages: 101

Brand: Airstream Pages: 98

Brand: TrailMax Pages: 58

FourTrax Foreman TRX500FE2 2018

Brand: Honda Pages: 279

Brand: Honda Pages: 229

Brand: Honda Pages: 159

Brand: Honda Pages: 71

Brand: Chevrolet Pages: 342

Brand: Toro Pages: 12

Brand: woodmizer Pages: 46

Brand: Superior Pages: 112

Track-O Twin-Track 47

Brand: Movex Pages: 37

Brand: American Landmaster Pages: 4

Brand: American Landmaster Pages: 49

07385 Workman HDX-D

Brand: Toro Pages: 60

Brand: Ski-Doo Pages: 152

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands