Can-Am 2009 DS 450 Operator'S Manual Download Page 13

Page: 13 / 152

SPECIAL SAFETY MESSAGES

WARNING

– Never exceed the stated load limits for this vehicle including operator, all

other added accessories.

– Always inspect and confirm the safe operating condition of your vehicle

prior to ride. Always follow the inspection and maintenance procedures
and schedules described in this Operator's Guide.

– Always use the tire size and type specified further in this Operator's

Guide. Always maintain proper tire pressure as described further in this
Operator's Guide.

– Never modify this vehicle through improper installation or use of acces-

sories. Only use BRP's approved accessories. NEVER install a passenger
seat or use the cargo area to carry a passenger.

European Community

This warning applies only in the European Countries where on road usage is
allowed.

WARNING

On road use:

– This vehicle is built for OFF-ROAD purposes only. It may be used for short

distances on paved surfaces at reduced speed, in order to move the vehi-
cle from an off-road location to another.

– When driving this vehicle on roads, always refrain from speeding and

substantially reduce vehicle speed when turning.

– Failure to do so can cause a loss of vehicle control, possibly resulting in

serious injury.

____________

SAFETY INFORMATION

___________

Summary of Contents for 2009 DS 450

























































































































































Search results

Summary of Contents for 2009 DS 450

Reviews:

Related manuals for 2009 DS 450

Brands by name

Popular brands

Can-Am 2009 DS 450, Operator'S Manual

Search results

Summary of Contents for 2009 DS 450

Reviews:

Related manuals for 2009 DS 450

Brands by name

Popular brands