Can-Am 2009 DS 450 Operator'S Manual Download Page 91

Page: 91 / 152

MAINTENANCE PROCEDURES

Start engine and let idle for a few min-
utes.

Ensure there are no leaks.

Stop engine and check oil level. Refill if
necessary.

Dispose oil as per your local environ-
mental regulations.

Engine Coolant

Engine Coolant Level

WARNING

Check coolant level with engine
cold. Never add coolant in cooling
system when engine is hot.

The engine coolant tank cap is locat-
ed underneath access cover near fuel
tank cap.

vmo2008-011-061_a

1. Coolant tank cap location

vmo2008-011-034

COOLANT TANK CAP

To remove access cover, proceed as
follow.

Remove seat.

vmo2008-011-026_c

1. Seat latch

Remove fuel tank cap.

vmo2008-011-028_c

Release cover tabs from fascia.

_____________________

Summary of Contents for 2009 DS 450

























































































































































Search results

Summary of Contents for 2009 DS 450

Reviews:

Related manuals for 2009 DS 450

Brands by name

Popular brands

Can-Am 2009 DS 450, Operator'S Manual

Search results

Summary of Contents for 2009 DS 450

Reviews:

Related manuals for 2009 DS 450

Brands by name

Popular brands