Can-Am 2009 DS 450 Operator'S Manual Download

Page: 130 / 152

MULTIFUNCTION GAUGE DISPLAY MESSAGES

MESSAGE

DESCRIPTION

LO BATT

Low battery voltage, check battery voltage and charging system.

HI BATT

High battery voltage, check battery voltage and charging system.

HI TEMP

(1)

Engine is overheating, refer to

ENGINE OVERHEAT

TROU-

BLESHOOTING GUIDELINES

LIMP HOME

Serious fault on the engine that can change the normal operation
of the engine, check engine indicator lamp will also blink, see an
authorized Can-Am dealer.

CHECK ENGINE

Engine fault, check engine indicator lamp will also be ON, see an
authorized Can-Am dealer.

NO ECM
COMMUNICATION

Communication error between gauge and engine control module
(ECM), see an authorized Can-Am dealer.

NOTICE

(1)

If the light does not turn off right after engine starting, stop en-

gine. See an authorized Can-Am dealer. Do not use the vehicle until repaired.

128

_____________________

Summary of Contents for 2009 DS 450

























































































































































Search results

Summary of Contents for 2009 DS 450

Reviews:

Related manuals for 2009 DS 450

Brands by name

Popular brands

Can-Am 2009 DS 450, Operator'S Manual

Search results

Summary of Contents for 2009 DS 450

Reviews:

Related manuals for 2009 DS 450

Brands by name

Popular brands