Can-Am 2009 DS 450 Operator'S Manual Download

Page: 63 / 152

CONTROLS/INSTRUMENT/EQUIPMENTS

Unit Selection (MPH vs km/h)

The speedometer, odometer and trip
meter are factory preset in miles but
it is possible to change them to kilo-
meter reading. Contact an authorized
Can-Am dealer.

Multifunction Display
(Normal Display Mode)

After vehicle startup, the normal dis-
play mode shows either:

– Vehicle speed
– Engine revolution per minute (RPM)
– Both parameters simultaneously

(combined mode).

Speed Mode

In this mode, the display shows the
speed of the vehicle either in km/h or
in MPH.

vmo2008-018-008

RPM Mode

In this mode, the display shows the en-
gine RPM.

vmo2008-018-009

Combined Mode

In this mode, the display shows the
speed of the vehicle and the engine
RPM.

vmo2008-018-010_a

1. Vehicle speed
2. Engine RPM

Mode Change

To change from one display to the oth-
er, proceed as follows.

1. Turn ignition key to ON. Wait until

“greeting message” is finished.

2. Press and release selector button

once to display OD (odometer).

vmo2008-018-009

3. Press selector button and HOLD

for 2 seconds. This will change the
displayed mode to either Speed,
RPM or Combined.

4. To select another mode, repeat

steps 2 and 3 until you get the
mode desired.

_____________________

Summary of Contents for 2009 DS 450

























































































































































Search results

Summary of Contents for 2009 DS 450

Reviews:

Related manuals for 2009 DS 450

Brands by name

Popular brands

Can-Am 2009 DS 450, Operator'S Manual

Search results

Summary of Contents for 2009 DS 450

Reviews:

Related manuals for 2009 DS 450

Brands by name

Popular brands