Can-Am 2009 DS 450 Operator'S Manual Download

Page: 102 / 152

MAINTENANCE PROCEDURES

WARNING

Always wear eye protection and
gloves when you lubricate a cable.

NOTE:

Place a rag around the cable lu-

ber to prevent the lubricant to splash.

Put the lubricant until it passes through
the cable.

vmo2008-011-102_a

1. Look for lubricant here

Reinstall the cable.

Spray a little quantity of lubricant on the
throttle lever mechanism then close
the housing.

Adjust the throttle lever.

Throttle Lever

Throttle Lever Adjustment

Slide rubber protector back to expose
throttle cable adjuster.

vmo2008-011-072_a

1. Rubber protector

Loosen lock nut then turn the adjuster
to obtain correct throttle lever free play.

vmo2008-011-073_a

1. Lock nut
2. Adjuster

NOTE:

Measure throttle free play at

the tip of throttle lever.

Tighten lock nut and reinstall protector.

While reading this Operator’s Guide, reminder that:

WARNING

Indicates a potential hazard that, if not avoided, could result in serious
injury or death.

100

_____________________

Summary of Contents for 2009 DS 450

























































































































































Search results

Summary of Contents for 2009 DS 450

Reviews:

Related manuals for 2009 DS 450

Brands by name

Popular brands

Can-Am 2009 DS 450, Operator'S Manual

Search results

Summary of Contents for 2009 DS 450

Reviews:

Related manuals for 2009 DS 450

Brands by name

Popular brands