Can-Am 2009 DS 450 Operator'S Manual Download Page 126 | Manualshive

Page: 126 / 152

background image

TECHNICAL GUIDELINES

ENGINE DOES NOT TURN

1. Ignition switch is in the OFF position.

– Place switch to the ON position.

2. Engine stop switch is in the OFF position.

– Place switch to the ON position.

3. Transmission is not set on NEUTRAL.

– Set transmission either in NEUTRAL or depress the clutch lever.

4. Weak battery or loose connections.

– Check connections and terminals condition.
– Have the battery checked.
– Contact an authorized Can-Am dealer.

ENGINE TURNS OVER BUT FAILS TO START

1. Blown fuse.

– Check fuel pump fuse.

2. Flooded engine (spark plugs wet when removed).

– (Drowned mode) If the engine does not start and it is fuel-flooded, this spe-

cial mode can be activated to prevent fuel injection while cranking. Proceed
as follows:
• Insert key in ignition switch and turn to ON position.
• Press completely and HOLD throttle lever.
• Press the engine START button.
The engine should be cranked for 20 seconds. Release engine START but-
ton.
Release throttle lever and start/crank engine again to allow starting.

If it does not work:

• Clean the spark plug caps area then remove them.
• Remove the spark plugs, refer to MAINTENANCE INFORMATION section.
• Crank engine several times.
• Install new spark plugs if possible or clean and dry spark plugs.
• Start engine as explained above.
If engine continues to flood, see an authorized Can-Am dealer.

NOTE:

Make sure to verify that there is no fuel in engine oil, if so, replace

engine oil.

3. No fuel to the engine (spark plugs dry when removed).

– Check fuel tank level.
– A failure of the fuel pump may have occurred.
– Check fuel pump fuse.
– Contact an authorized Can-Am dealer.

124

_____________________

«
...
124
125
126
127
128
...
»

Summary of Contents for 2009 DS 450

























































































































































Reviews:

No comments

Related manuals for 2009 DS 450

Brand: J&M Pages: 26

1993 TRX300 TOURTRAX 300

Brand: Honda Pages: 158

INDUSTRIAL 1200

Brand: Ezgo Pages: 148

Brand: Honda Pages: 83

Brand: Morooka Pages: 134

Brand: Dongfang Motor Pages: 19

Sniper T-1500 2S

Brand: BMS Pages: 69

Brand: TGB Pages: 269

Brand: TGB Pages: 306

Brand: Can-Am Pages: 144

Brand: HYOSUNG Pages: 60

Steely 1260.400

Brand: Humbaur Pages: 4

Brand: Polaris Pages: 220

OneStopGardens 91240

Brand: Harbor Freight Tools Pages: 7

jay 2016 series

Brand: Jayco Pages: 157

Brand: Landoll Pages: 70

DewEze 400 Series

Brand: Harper Pages: 75

GRIZZLY 700 2013

Brand: Yamaha Pages: 174

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands