manualshive.com logo in svg

Can-Am 2009 DS 450, Operator'S Manual

The Can-Am 2009 DS 450 Operator's Manual is a comprehensive guide designed to assist you in properly operating and maintaining your Can-Am 2009 DS 450 ATV. Obtain expert guidance at your fingertips by downloading the free manual from our website, ensuring a seamless user experience.

Share
Download
background image

TABLE OF CONTENTS

FOREWORD . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .

1

Know Before you Go .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .

1

Safety Messages.. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .

1

About this Operator's Guide . . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .

1

SAFETY INFORMATION

GENERAL PRECAUTIONS. .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .

8

Avoid Carbon Monoxide Poisoning .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .

8

Avoid Gasoline Fires and Other Hazards . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .

8

Avoid Burns from Hot Parts .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .

8

Accessories and Modifications .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .

8

SPECIAL SAFETY MESSAGES . . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .

9

European Community . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 11

OPERATION WARNINGS . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 12

RIDING THE VEHICLE . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 36

Pre-Ride Inspection . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 37
Clothing . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 38
Carrying Loads . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 39
Recreational Riding . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 40
Environment . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 40
Design Limitation . . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 41
Off-Highway Operation . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 41
General Operating and Safety Precautions . . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 41
Riding Techniques. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 42

HANG TAG. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 48

IMPORTANT ON PRODUCT LABELS .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 49

VEHICLE INFORMATION

CONTROLS/INSTRUMENT/EQUIPMENTS .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 54

1) Throttle Lever . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 56
2) Front Brake Lever .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 56
3) Clutch Lever . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 57
4) Parking Brake Lever . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 57
5) Headlights Dimmer Switch . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 58
6) Turn Signal Switch .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 59
7) Engine Stop Switch . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 59
8) Horn Button . . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 59
9) Hazard Warning Button . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 59
10) Engine Start Button . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . 60

______________________

3

Summary of Contents for 2009 DS 450

























































































































































Reviews:

No comments

Related manuals for 2009 DS 450

Wacker Neuson 1001 Operator'S Manual preview
1001
Brand: Wacker Neuson Pages: 164
TransTank GlidePath Operator'S Handbook Manual preview
GlidePath
Brand: TransTank Pages: 28
Toro Twister 12003 Operator'S Manual preview
Twister 12003
Brand: Toro Pages: 32
Polaris ACE 500 2017 Owner'S Manual For Maintenance And Safety preview
ACE 500 2017
Brand: Polaris Pages: 174
Yamaha ET340ED Supplementary Service Manual preview
ET340ED
Brand: Yamaha Pages: 13
Yamaha EX440D Supplemental Service Manual preview
EX440D
Brand: Yamaha Pages: 14
Yamaha ET340D Supplementary Service Manual preview
ET340D
Brand: Yamaha Pages: 13
Yamaha G-Max G22A Owner'S And Operator'S Manual preview
G-Max G22A
Brand: Yamaha Pages: 47
Yamaha CAMSO Installation Manuallines preview
CAMSO
Brand: Yamaha Pages: 16
Yamaha GRIZZLY 125 YFM125GY Owner'S Manual preview
GRIZZLY 125 YFM125GY
Brand: Yamaha Pages: 130
Yamaha GRIZZLY 125 YFM125GZ Owner'S Manual preview
GRIZZLY 125 YFM125GZ
Brand: Yamaha Pages: 132
Yamaha G1AM4 Owner'S/Operator'S Manual preview
G1AM4
Brand: Yamaha Pages: 100
Yamaha DRIVE 2 2022 Owner'S/Operator'S Manual preview
DRIVE 2 2022
Brand: Yamaha Pages: 64
Yamaha GRIZZLY 125 YFM125GD Owner'S Manual preview
GRIZZLY 125 YFM125GD
Brand: Yamaha Pages: 134
Yamaha GRIZZLY 125 YFM125GA Owner'S Manual preview
GRIZZLY 125 YFM125GA
Brand: Yamaha Pages: 132
Yamaha FX Nytro Owner'S Manual preview
FX Nytro
Brand: Yamaha Pages: 104
Yamaha EC340M 1988 Owner'S Manual preview
EC340M 1988
Brand: Yamaha Pages: 124
Yamaha FX Nytro FX10MTRAX Assembly Manual preview
FX Nytro FX10MTRAX
Brand: Yamaha Pages: 152

Brands by name

Popular brands

Load more brands