Can-Am 2009 DS 450 Operator'S Manual Download

Page: 28 / 152

OPERATION WARNINGS

WARNING

V00A0GQ

POTENTIAL HAZARD

Going down a hill improperly.

WHAT CAN HAPPEN

Could cause loss of control or cause vehicle to overturn.

HOW TO AVOID THE HAZARD

Always follow proper procedures for going down hills as described further
in this Operator's Guide.

NOTE: A special technique is required when braking as you go down a hill.

Always check the terrain carefully before you start down any hill.

Shift your weight backward.

Never go down a hill at high speed.

Avoid going down a hill at an angle which would cause the vehicle to lean
sharply to one side. Go straight down the hill where possible.

___________

SAFETY INFORMATION

____________

Summary of Contents for 2009 DS 450

























































































































































Search results

Summary of Contents for 2009 DS 450

Reviews:

Related manuals for 2009 DS 450

Brands by name

Popular brands

Can-Am 2009 DS 450, Operator'S Manual

Search results

Summary of Contents for 2009 DS 450

Reviews:

Related manuals for 2009 DS 450

Brands by name

Popular brands