Can-Am 2009 DS 450 Operator'S Manual Download Page 69 | Manualshive

Page: 69 / 152

background image

FUEL

Recommended Fuel

Use premium unleaded gasoline, avail-
able from most service stations or oxy-
genated fuel containing a maximum to-
tal of 10% of ethanol or methanol. The
gasoline used must have the following
recommended minimum octane rat-
ing.

MINIMUM OCTANE RATING

95 RON

NOTICE

Never experiment with

other fuels. The use of non rec-
ommended fuel can result in vehi-
cle performance deterioration and
damage to critical parts in the fuel
system and engine components.

Fueling Procedure

NOTICE

Never

place

anything

over fuel tank cap because the vent
hole on the top of fuel tank cap can
be blocked and the engine could
misfire.

Unscrew counterclockwise and re-
move cap to allow fuel tank filling then
fully tighten clockwise.

Position vent tube in steering column.

vmo2008-011-106_a

TYPICAL

1. Fuel tank cap
2. Vent tube

WARNING

Always stop engine before refu-
eling. Open cap slowly. If a dif-
ferential pressure condition is no-
ticed (whistling sound heard when
loosening fuel tank cap) have ve-
hicle inspected and/or repaired
before further

operation.

Fuel

is flammable and explosive un-
der certain conditions. Never use
an open flame to check fuel lev-
el. Never smoke or allow flame or
spark in vicinity. Always work in
a well-ventilated area. Never top
up the fuel tank before placing the
vehicle in a warm area. As tem-
perature increases, fuel expands
and may overflow. Always wipe
off any fuel or oil spillage from the
vehicle.

While reading this Operator’s Guide, reminder that:

WARNING

Indicates a potential hazard that, if not avoided, could result in serious
injury or death.

_____________________

67

«
...
67
68
69
70
71
...
»

Summary of Contents for 2009 DS 450

























































































































































Reviews:

No comments

Related manuals for 2009 DS 450

Transporta CCT 5221

Brand: Ifor Williams Trailers Pages: 45

DIRT QUAD 25117460

Brand: Razor Pages: 12

Vyper 4WD 1100cc 4 seater XY1100UEL

Brand: gio Pages: 261

Brand: Can-Am Pages: 147

Brand: Erde Pages: 4

Brand: Polaris Pages: 5

Brand: Polaris Pages: 174

Brand: E-Z-GO Pages: 78

Brand: Yamaha Pages: 497

Brand: Eagle Pages: 29

Brand: Suzuki Pages: 136

Brand: PRONAR Pages: 133

Brand: PRONAR Pages: 136

Brand: Arctic Cat Pages: 59

Brand: Arctic Cat Pages: 80

Brand: Arctic Cat Pages: 84

Brand: Arctic Cat Pages: 64

Brand: Arctic Cat Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands