Can-Am 2009 DS 450 Operator'S Manual Download

Page: 79 / 152

VEHICLE TRANSPORTATION

When transporting a vehicle, secure
vehicle to trailer or pickup box with
suitable tie-downs.

Using ordinary

ropes is not recommended.

WARNING

Never tip this vehicle on end for
transporting. We recommend that
you carry the vehicle in its nor-
mal operating position (on all 4
wheels).

V00A18Y

Remember to:

– Apply the parking brake and place

the transmission in 1

gear.

– Secure the vehicle, using the appro-

priate areas. See the following illus-
tration.

NOTICE

Attaching vehicle at other

locations may damage the vehicle.

vmo2008-011-039_a

TYPICAL

vmo2008-011-098_a

TYPICAL

NOTICE

Attaching vehicle at other

locations may damage the vehicle.

WARNING

Do not tow this vehicle behind a
car or other vehicle. Use a trailer.

_____________________

Summary of Contents for 2009 DS 450

























































































































































Search results

Summary of Contents for 2009 DS 450

Reviews:

Related manuals for 2009 DS 450

Brands by name

Popular brands

Can-Am 2009 DS 450, Operator'S Manual

Search results

Summary of Contents for 2009 DS 450

Reviews:

Related manuals for 2009 DS 450

Brands by name

Popular brands