background image

‘                                                                                                                                                                                                       ‘

‘

‘

8

37

To operate your test probe, connect the 

BLACK

 clip to a 

good chassis

ground

. Then connect the 

RED

 clip to a 

good 12V (+) positive

 source.

If the test probe is connected correctly, both the 

GREEN

 and the 

RED

 lights

will be dimly illuminated. If a 

(+) positive

 source is probed, the 

RED

 light

will glow bright and the 

GREEN

 light will go out. If a 

(-) negative

 source

is probed, the 

GREEN

 light will glow bright and the 

RED

 light will go out.

USING YOUR TEST PROBE

1.  Strip back two inches of insulation on the wire from the remote 

starter.

TTwo Inches of Bare Wire

wo Inches of Bare Wire

MAKING WIRING CONNECTIONS

OPERATION

PRECAUTIONS

If your vehicle is equipped with air bags or a supplemental restraint systems

(SRS) and you CAN NOT identify the air bag wires, STOP THE INSTALLATION

IMMEDIATELY and have a professional identify the air bag wires before continuing

the installation.

WARNING! GENERAL MOTORS

REAR WHEEL DRIVE VEHICLES AND DODGE DAKOTAS

All General Motors rear wheel drive vehicles and Dodge Dakotas built prior

to 1996 do not have an electrical Neutral Safety switch. They have a

mechanical neutral safety switch. The mechanical neutral safety switch

operates as follows.

a)The key will only turn to start position when the gear selector is in park

or neutral.

b)The key can only be removed from the ignition switch when the gear

selector is in the park position.

You must use special precautions with this system.

D. CAR LOCATOR

Press the   button twice to active car locator function. The horn will chirp

(6) times. The parking light will flash (12) times, for you to easily locate

your car.

E. PANIC FUNCTION:

The transmitter can be used as a remote panic switch to manually trigger

the alarm in case emergency.

1. Press and hold the   button for (3) seconds. The horn (if installed)

will immediately sound.

2. During panic mode, the normal function of this transmitter button 

will be suspended.

3. To stop the alarm, press and hold   button on the transmitter again

for (3) seconds.

4. If the button is not pressed, the alarm will automatically stop after

30 seconds.

F. DOME LIGHT CONVENIENCE DELAY & SUPERVISION

Upon disarming, the interior light will remain on for 30 seconds.

Note: Turning on the ignition switch or locking the vehicle’s door will turn

off the dome light.

G. IGNITION CONTROL DOOR LOCK/UNLOCK.

.

If the vehicles door locks have been interfaced to the system, the system

will automatically lock the vehicle's doors when the ignition is turned

“ON” and /or unlock the vehicle’s doors when the ignition is turned “OFF”.

H. TRUNK RELEASE (CHANNEL 3) OUTPUT.

Press and hold

 

 button on the transmitter for (2) seconds to operate

the trunk release or other electric devices.

I. DRIVER PAGING / LOST & FOUND

(For two-way transceiver operation only)

It is useful in the event that someone wants to page the

driver of the parked vehicle or someone cannot find his LCD

remote control transceiver. With the ignition switch “off”,

press and hold the valet switch for (2) seconds to page the

driver, one chirp sound shall be emitted from the vehicle and

the paging melody sound continues sounding from the Remote LCD

transceiver and “

” indication flashes on the LCD screen.

Summary of Contents for DELUXE 200























Reviews: