18
27
PROGRAMMING
4. Within (10) seconds, start the vehicle with the key. (While the engine
is running, the parking lights and LED will flash, If they are not flashing
please check
VIOLET/WHITE
wire connection.
5. Press and hold the Program switch for (2) seconds until a long chirp and
the LED light will glow constantly on for two seconds. The RPM signal
is now learned.
6. Turns off the ignition switch to stop engine from running.
Once you complete step 6, you can adjust and test Check Level as below:
CRANK TIME ADJUST / HI OR LOW LEVEL CHECK
1. Press the
button
twice
on the transmitter to start the vehicle.
2. If everything goes well:
a. Press the
button
twice
on the transmitter to stop engine running.
You have completed this programming successfully.
b. Press
button
on the transmitter to exit the program mode. There
will be
(3) long chirps
and
(3) parking light flashes
for confirmation.
3. If the crank time is too short, (Engine not running, before the starter
stops cranking):
a. Press the
button
twice
on the transmitter to turn the ignition off.
Press
button
on the transmitter to set proper
Check Level
to
Hi position.
(1) LED flash
and
(1) chirp
will confirm this setting.
b. Repeat the steps 1 4.
ENGINE CHECK VOLTAGE:
Important Note:
The Check Level for most vehicles should be set in Hi
Check Level
,
while in Engine Check Voltage mode, the Check Level
must be set at HI position before proceeding.
1. Turn the Ignition switch
ON/OFF (3) TIMES
and leave in the
OFF
position.
2. Push the Program switch (8) times and hold in on the 8
th
push until
(4) chirps with a long chirp is heard then release the Program switch.
3. Press the transmitter and buttons at the same time to set the Engine
Check Voltage. (1) LED flash, (1) chirp to confirm this setting
Once you complete step 3, you can adjust and test Start Timer
as below:
WIRING CONNECTIONS
This wire provides an instant
shutdown for the remote start,
whenever it is grounded. Connect
the wire to the hood pin switch
previously installed. This wire must
be routed though a grommet in the
firewall and connected to the hood
pin switch. If the pin switch is to
be used with an alarm system,
connect this wire with a diode.
H4/5 - Red / White wire (-) 200ma Channel 3 (Trunk) Output
This will become a 1 second pulse ground by activateing channel 3 on
transmitter for (2) seconds. The current capacity of this wire is 200 mA.
This feature allows you to remote control trunk release or other electric
device.
H4/6 - Brown / Black wire (-) 200mA Factory Security Rearm
Signal / Key Sensor Output
Factory Security Rearm Signal Output (Factory default setting.)
This output is programmable. If programmed it can rearm a factory
installed security system. This wire will supply a pulse whenever the
remote start times out or is shut down using the transmitter and remote
door locking..
Ground Output During Start (Crank)
This wire will provide a 200mA ground output while the starter output of
the remote start unit is active. This output can be used to activate the
Crank Low/Bulb Test wire found in some GM vehicles. This wire is also
referred to as the ECM wake up wire in some vehicles.
H6 2-PIN BLUE CONNECTOR FOR THE PROGRAM SWITCH:
Select a mounting location for the switch that is easily accessible to the
driver of the vehicle. The switch does not have to be concealed. however,
concealing the switch is always recommended. Route the program switch
wires to the control module.
H4/7 - Black/White wire (-) 200mA Dome Light Supervision Output
This wire becomes grounded when the dome light controls circuit is active.
The current capacity of this wire is 200mA. This wire can control the
operation of the interior lights. An optional 10 Amp relay can be used for
systems which draw more than 200mA and/or positive voltage systems
interior lights operation. Upon disarming, the interior lights will remain
on for 30 seconds.
Summary of Contents for DELUXE 200
Page 1: ......
