Synergy Technician's Software Reference Page 8
■
Jog Backward
: Moves the motor
backward a variable number of
inches.
■
Stop
: Performs a hard stop on the
motor.
●
Page 5
: First Page of Belt Settings. Belts are
assumed to be ordered (ie Belt 1 is before Belt 2 is
before Belt 3).
○
Belts -F
: The number of Belts in the Sys
-
tem
○
Transfer Tolerance -F
: The distance from
an edge of a belt where, if a garment is
within that distance, a transfer will begin.
○
Max Transfer Velocity -F
: The maximum
velocity at which a system performs a
garment transfer between belts. Any value
over 15 in/s requires Advanced Motors to
coordinate.
○
FFY Transfer Multiplier -F
: The relative
speed the Transfer Belt operates at when
transferring garments from the Transfer
Belt to the Firefly.
○
Pretreater Belt ID -F
: The ID of the Belt
associated with the Synergy.
○
PTR Acceleration -F
: The Acceleration
at which the Pretreater Belt operates. If
changing this value it is advised to also
change the Transfer Belt value.
○
PTR Velocity -F
: The Velocity at which
the Pretreater Belt typically operate.
○
PTR Return Velocity -F
: The Velocity
at which the Pretreat Belt will perform
Return
operations.
○
Transfer Belt ID -F
: The ID of the Belt
associated with the Transfer Belt between
the Synergy Pretreater and Firefly Dryer.
○
XFR Acceleration -F:
The Acceleration
that the Transfer Belt operates. If changing
this value, it is advised to also change the
Pretreater Belt value.
○
XFR Velocity -F
: The Velocity at which
the Pretreater Belt will typically operate.
○ Firefly Belt ID -F
: The ID of the Belt
associated with the Firefly.
○
FFY Lane -F
: The Firefly Lane the Syner
-
gy system is connected to. (begins at 1)
○
FFY Drone Length -F
: The combined
length of the Firefly Drones.
○
FFY Acceleration -F
: The Acceleration
the Firefly Belt operates at.
○
Cleaning Belt Velocity
: During the
Clean
Belt Operation
as defined in the
System
Maintenance Card
Section, this indicates
how fast the belts move.
○
Cleaning Auto-Spray
: During the
Clean
Belt Operation
as defined in the
System
Maintenance Card
Section, this indicates
if the carriage should automatically sweep
and spray water during the operation.
○
Cleaning Spray Velocity
: During the
Clean Belt Operation
as defined in the
System Maintenance Card
Section, this
indicates how fast the carriage moves
during its spray sweeps.
○
Cleaning Spray Front -I
: During the
Clean Belt Operation
as defined in the
System Maintenance Card
Section, this
indicates where the carriage stops during
its return sweep.
○
Cleaning Spray Back -I
: During the
Clean Belt Operation
as defined in the
System Maintenance Card
Section, this
indicates where the carriage stops during
its forward sweep.
○
Belt
: Selects which Belts settings are
visible.
■
Belt Motor -F
: The ID of the Mo
-
tor that drives that belt.
■
Length -F
: The length of the belt
●
Page 6
: Zone and Projector Settings
○
Zone Tolerance -F
: How tightly and
accurately the system checks if the belt
has moved to its target position. If set too
small the belt can jitter back and forth after
a large move.
○
Default Garment -I
: The Width of the De
-
fault Garment that is loaded in the system.
Affects how long transfers takes and where
the system believes the garment is.
○
Garment Front Buffer -I
: The amount
of extra length added to the front of each
garment. Affects how long transfers take.
Can protect garments from getting stuck
between belts.
○
Garment Rear Buffer -I
: The amount
of extra length added to the end of each
garment. Affects how long transfers take.
Can protect garments from getting stuck
between belts.
○
Toggle Calibration
: Puts the Projector into
Calibration mode, showing an all white
display with text assigning terms to edges
of the projection.
○
Rotate -I
: Rotates the Projected image 90
degrees each time it is pressed. Used to
adjust the location of the Nearest Edge.
○
Flip -I
: Rotates the Projected image 180
degrees each time it is pressed. Used to
adjust the location of the Nearest Edge.
○
Minor /- -I
: Performs a minor
rotation of 0.5 degrees of the load zones
red box each time it is pressed. Used to
