Brocade Communications Systems ICX 7250 Hardware Installation Manual Download Page 76 | Manualshive

Page: 76 / 119

background image

NOTE
The device shown in the diagram may be different from the one you are using. The process to remove the EPS4000 faceplate
is the same.

FIGURE 53 Removing the EPS4000 faceplate on the ICX 7250 device

1.

Faceplate screws

1.

Using a Phillips screwdriver, remove the two screws on the EPS4000 faceplate of the external power receptacle.

2. Attach the port side connector of the EPS4000 DC cord to the switch.
3. Attach the EPS4000 side connector of the EPS4000 DC cord to an available DC power port on the back of the EPS4000.
4. Use a flat-blade screwdriver to attach the latch screw on the DC cord to the EPS4000.

When the screw is tightened securely, all power supplies to your device will be active.

Powering on the system

After you complete the physical installation, you can power on the system.

NOTE
The power outlet should be installed near the equipment and should be easily accessible.

1.

Remove the power cord from the shipping container.

Installing the EPS4000

Brocade ICX 7250 Switch Hardware Installation Guide

76

53-1003898-02

«
...
74
75
76
77
78
...
»

Summary of Contents for ICX 7250
























































































































Reviews:

No comments

Related manuals for ICX 7250

Brand: Ubisys Pages: 40

Brand: Campbell Pages: 14

Brand: Dataprobe Pages: 21

SilverStorm 9000

Brand: Qlogic Pages: 50

QuantaMesh T1048-LB9

Brand: QCT Pages: 42

OmniView Secure F1DN102Uea

Brand: Belkin Pages: 36

Brand: FS Pages: 33

Brand: J-Tech Digital Pages: 28

Brand: Generac Power Systems Pages: 20

Brand: Hamlet Pages: 2

Brand: Scame electrical solutions Pages: 68

Brand: J-Tech Digital Pages: 13

Brand: Versa Technology Pages: 96

Brand: Witura Pages: 12

Brand: Lindy Pages: 7

Brand: Gefen Pages: 31

Brand: Murphy Pages: 24

Brand: JUKI Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands