Brocade Communications Systems ICX 7250 Hardware Installation Manual Download Page 103

Page: 103 / 119

Model

Height

Width

Depth

Weight

1.72 in

17.32 in

14.6 in

10.6 lb

ICX 7250-48P

4.37 cm

1.72 in

44.0 cm

17.32 in

37 cm

14.6 in

5.9 kg

13.0 lb

Environmental requirements

Condition

Operational

Non-operational

Ambient temperature

-5°C to 50°C (23°F to 122°F)

-25°C to 70°C (-13°F to 158°F)

Relative humidity (non-
condensing)

5% to 95% at 50°C (122°F)

5% to 95% at 70°C (158°F)

Altitude (above sea level)

0 to 3,000 m (10,000 feet)

0 to 12,000 m (39,000 feet)

Shock

20 G, 11 ms, half-sine wave

33 G, 11 ms, half-sine wave

Vibration

1 G sine, 0.4 gms random, 5-500 Hz

2.4 G sine, 1.1 gms random, 5-500 Hz

Airflow

ICX 7250-24G: 14.3 CFM (Maximum), 5.7 CFM (Typical)

ICX 7250-24 : 14.0 CFM (Maximum), 5.7 CFM (Typical)

ICX 7250-24P: 34.4 CFM (Maximum), 13.7 CFM (Typical)

ICX 7250-48: 34.8 CFM (Maximum), 13.8 CFM (Typical)

ICX 7250-48P: 45.2 CFM (Maximum), 21.4 CFM (Typical)

N/A

Heat dissipation

Refer to Power Consumption specification sections

N/A

Operating noise

ICX 7250-24G: 40 dBA

ICX 7250-24: 41.9 dBA

ICX 7250-24P: 44.7 dBA

ICX 7250-48: 44.5 dBA

ICX 7250-48P: 45.9 dBA

N/A

Power supply specifications (per PSU)

The EPS4000 and its power supply modules (RPS17) are field-replaceable. All other Brocade ICX 7250 power supply units (PSUs) are
fixed and internal to the devices. All the PSUs use a C14 inlet and connect to standard AC power.

NOTE
The EPS4000 must have at least one RPS17 installed to provide power to the supported Brocade ICX 7250 devices.

Device

Maximum output
power rating (DC)

Input voltage

Input line
frequency

Maximum input
current

Input line
protection

Maximum inrush
current

ICX 7250-24G

ICX 7250-24

65 W

100 - 240 VAC

(nominal)

90 - 264 VAC

(range)

50/60 Hz

(nominal)

47 - 63 Hz

(range)

1.5 A (rms)

Line fused

40 A at 115 VAC

80 A at 230 VAC

Cold start @ 25°C

ICX 7250-24P

525 W

100 - 240 VAC

(nominal)

90 - 264 VAC

50/60 Hz

(nominal)

47 - 63 Hz

6 A (rms)

Line fused

30 A at 115 VAC

60 A at 230 VAC

Cold start @ 25°C

Brocade ICX 7250 Switch Technical Specifications

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

103

Summary of Contents for ICX 7250
























































































































Search results

Summary of Contents for ICX 7250

Reviews:

Brands by name

Popular brands

Brocade Communications Systems ICX 7250, Hardware Installation Manual

Search results

Summary of Contents for ICX 7250

Reviews:

Brands by name

Popular brands