manualshive.com logo in svg

Brocade Communications Systems ICX 7250, Hardware Installation Manual

Share
Download
Brocade Communications Systems ICX 7250 Hardware Installation Manual Download Page 98

FIGURE 56 Unlocking the bail latch

1.

Bail latch

NOTE
The bail latch may be attached to either the top or the bottom of the SFP transceiver.

4. Grasp the bail latch and pull the copper or fiber-optic module out of the port.

FIGURE 57 Removing the fiber-optic module

5. Store the copper or fiber-optic module in a safe, static-free place or in an anti-static bag.
6. If you are installing a new module, install the new copper or fiber-optic module in the port. For instructions to install a fiber-optic

transceiver, refer to 

Installing a fiber-optic transceiver

 on page 98.

Installing a fiber-optic transceiver

You can install a new fiber-optic transceiver in an SFP or SFP+ slot while the device is powered on and running.

While installing a transceiver, wear an ESD wrist strap with a plug that can be inserted in the ESD connector on the ICX 7250 device.

DANGER

For safety reasons, the ESD wrist strap should contain a series 1 megaohm resistor.

DANGER

All fiber-optic interfaces use Class 1 lasers.

Perform the following steps to install a fiber-optic transceiver.

1.

Put on the ESD wrist strap and ground yourself by attaching the clip end to a metal surface (such as an equipment rack) to act
as ground.

Hardware Maintenance Schedule

Brocade ICX 7250 Switch Hardware Installation Guide

98

53-1003898-02

Summary of Contents for ICX 7250
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands