Brocade Communications Systems ICX 7250 Hardware Installation Manual Download Page 24

Page: 24 / 119

Summary of installation tasks

Follow the steps in the following table to install your device. Details for each of these steps are provided on the pages indicated.

TABLE 7 Installation tasks

Task number

Task

Where to find more information

Ensure that the physical environment that will
host the device has the proper cabling and
ventilation.

Preparing the installation site

on page 25

Unpack the device and all included accessories.

Items included with the ICX 7250 device

page 23

Install the device on a desktop, or in an
equipment rack.

Installing the device

on page 26

Once the device is installed, plug the device into
a nearby power source that adheres to the
regulatory requirements outlined in this manual.

Powering on the system

on page 62

Installation precautions

Follow all precautions when installing a device.

General precautions

DANGER

All fiber-optic interfaces use Class 1 lasers.

CAUTION
Do not install the device in an environment where the operating ambient temperature might exceed 50°C (122°F).

CAUTION
Make sure the airflow around the front, sides, and back of the device is not restricted.

Lifting precautions

DANGER

Make sure the rack housing the device is adequately secured to prevent it from becoming unstable or falling over.

DANGER

Mount the devices you install in a rack as low as possible. Place the heaviest device at the bottom and progressively place
lighter devices above.

Power precautions

CAUTION
Use a separate branch circuit for each power cord, which provides redundancy in case one of the circuits fails.

Installation

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

Summary of Contents for ICX 7250
























































































































Search results

Summary of Contents for ICX 7250

Reviews:

Related manuals for ICX 7250

Brands by name

Popular brands

Brocade Communications Systems ICX 7250, Hardware Installation Manual

Search results

Summary of Contents for ICX 7250

Reviews:

Related manuals for ICX 7250

Brands by name

Popular brands