manualshive.com logo in svg

Brocade Communications Systems ICX 7250, Hardware Installation Manual

Share
Download
Brocade Communications Systems ICX 7250 Hardware Installation Manual Download Page 91

TABLE 12 Network connection-related LED states (continued)

LED

Desired state

Meaning

Abnormal
state

Meaning or action

∙

Verify that the port has not been
disabled through a configuration
change.

∙

Ensure that the SFP+
transceivers in both ends are of
the same optic type (for example,
SR, LR, LRM).

∙

If the other actions do not resolve
the problem, try using a different
port or a different cable.

If a problem persists after taking these actions, contact Brocade Technical Support.

Tracing a route

To determine the path through which a Brocade device can reach another device, enter a command similar to the following at any level
of the CLI on the device.

device> traceroute 10.33.4.7

The CLI displays trace route information for each hop as soon as the information is received. Traceroute requests display all responses
to a given TTL. In addition, if there are multiple equal-cost routes to the destination, the Brocade device displays up to two responses by
default.

Configuring the Device

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

91

Summary of Contents for ICX 7250
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands