manualshive.com logo in svg

Brocade Communications Systems ICX 7250, Hardware Installation Manual

Share
Download
Brocade Communications Systems ICX 7250 Hardware Installation Manual Download Page 73

1.

Put on the ESD wrist strap and ground yourself by attaching the clip end to a metal surface (such as an equipment rack) to act
as ground.

2. Remove the four screws that hold the PSU slot cover in place.

FIGURE 50 Installing an RPS17 PSU

1.

RPS17 PSU slots (3 populated, 1 available)

2. Screws

NOTE
If you are replacing an RPS17 PSU, you must uninstall a PSU. Refer to 

Uninstalling an RPS17 PSU

 on page 73.

3. Remove the new PSU from the protective packaging.
4. Gently insert the PSU into the slot until it clicks into place.

Uninstalling an RPS17 PSU

You can uninstall an RPS17 PSU from the EPS4000while the device is powered on and running.

NOTE
While uninstalling a PSU, wear an ESD wrist strap.

DANGER

For safety reasons, the ESD wrist strap should contain a series 1 megaohm resistor.

Perform the following steps to uninstall an RPS17 PSU.

1.

Put on the ESD wrist strap and ground yourself by attaching the clip end to a metal surface (such as an equipment rack) to act
as ground.

2. Lift the PSU latch and gently slide the PSU out from the slot.

Installing the EPS4000

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

73

Summary of Contents for ICX 7250
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands