Brocade Communications Systems ICX 7250 Hardware Installation Manual Download Page 36

Page: 36 / 119

FIGURE 19 Attaching the medium or long rear brackets to the extensions

Rear bracket, medium or long

Screws, 6-32 x 1/4-in., panhead Phillips

Attaching the rear brackets to the rack posts

Complete the following steps to attach the rear brackets to the rack posts.

Attach the right rear bracket to the right rear rack post using two 10-32 x 5/8-in. panhead screws and two retainer nuts, as
shown in

Figure 20

. Use the upper and lower holes in the bracket.

2. Attach the left rear bracket to the left rear rack post using two 10-32 x 5/8-in. panhead screws and two retainer nuts. Use the

upper and lower holes in the bracket.

3. Tighten all the 10-32 x 5/8-in. screws to a torque of 25 in-lb (29 cm-kg).

Installation

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

Summary of Contents for ICX 7250
























































































































Search results

Summary of Contents for ICX 7250

Reviews:

Related manuals for ICX 7250

Brands by name

Popular brands

Brocade Communications Systems ICX 7250, Hardware Installation Manual

Search results

Summary of Contents for ICX 7250

Reviews:

Related manuals for ICX 7250

Brands by name

Popular brands