manualshive.com logo in svg

Brocade Communications Systems ICX 7250, Hardware Installation Manual

Share
Download
Brocade Communications Systems ICX 7250 Hardware Installation Manual Download Page 51

FIGURE 32 Attaching the rear brackets to the rack posts

1.

Screws, 10-32 x 5/8-in., panhead Phillips

2.

Retainer nuts, 10-32

Flush-rear (recessed) mounting

The flush-rear (recessed) mounting is similar to the flush-front mounting except that the brackets are reversed on the device.

CAUTION
The device must be turned off and disconnected from the fabric during this procedure.

NOTE
The illustrations in the rack installation procedures show a 1U device, but the instructions are the same for a 2U device. The
illustrations in the rack installation procedures are for reference only and may not show the actual device.

Complete the following tasks to install the device in a four-post rack:

1.

Attaching the front brackets to the rear of the device

 on page 51

2.

Attaching the extensions to the front of the device

 on page 52

3.

Installing the device in the rack

 on page 53

4.

Attaching the rear brackets to the extensions at the front of the device

 on page 54

5.

Attaching the rear brackets to the front rack posts

 on page 56

Attaching the front brackets to the rear of the device

NOTE
In this installation, the brackets are named as listed in the parts list even though the installation of the brackets is reversed from
the flush-front installation.

Installation

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

51

Summary of Contents for ICX 7250
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands