Brocade Communications Systems ICX 7250 Hardware Installation Manual Download Page 79

Page: 79 / 119

Condition

Operational

Non-operational

Four PSUs installed : 53.4 dBA

Regulatory compliance (EMC)

∙

FCC Part 15, Subpart B (Class A)

∙

EN 55022 (CE mark) (Class A)

∙

EN 55024 (CE mark) (Immunity) for Information Technology Equipment

∙

ICES-003 (Canada) (Class A)

∙

AS/NZ 55022 (Australia) (Class A)

∙

VCCI (Japan) (Class A)

∙

EN 61000-3-2

∙

EN 61000-3-3

∙

EN 61000-6-1

Regulatory compliance (safety)

∙

CAN/CSA-C22.2 No. 60950-1-07/UL60950-1 - Safety of Information Technology Equipment

∙

EN 60825-1 Safety of Laser Products - Part 1: Equipment Classification, Requirements and User's Guide

∙

EN 60825-2 Safety of Laser Products - Part 2: Safety of Optical Fibre Communications Systems

∙

EN 60950-1, IEC 60950-1 Safety of Information Technology Equipment

Regulatory compliance (environmental)

∙

2011/65/EU - Restriction of the use of certain hazardous substance in electrical and electronic equipment (EU RoHS)

∙

2012/19/EU - Waste electrical and electronic equipment (EU WEEE)

∙

94/62/EC - packaging and packaging waste (EU)

∙

2006/66/EC - batteries and accumulators and waste batteries and accumulators (EU battery directive)

∙

1907/2006 of the European Parliament and of the Council of 18 December 2006 concerning the Registration, Evaluation,
Authorisation and Restriction of Chemicals (EU REACH)

∙

Section 1502 of the Dodd-Frank Wall Street Reform and Consumer Protection Act of 2010 - U.S. Conflict Minerals

∙

30/2011/TT-BCT - Vietnam circular

∙

SJ/T 11363-2006 Requirements for Concentration Limits for Certain Hazardous Substances in EIPs (China)

∙

SJ/T 11364-2006 Marking for the Control of Pollution Caused by EIPs (China)

Installing the EPS4000

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

Summary of Contents for ICX 7250
























































































































Search results

Summary of Contents for ICX 7250

Reviews:

Related manuals for ICX 7250

Brands by name

Popular brands

Brocade Communications Systems ICX 7250, Hardware Installation Manual

Search results

Summary of Contents for ICX 7250

Reviews:

Related manuals for ICX 7250

Brands by name

Popular brands