manualshive.com logo in svg

Brocade Communications Systems ICX 7250, Hardware Installation Manual

Share
Download
Brocade Communications Systems ICX 7250 Hardware Installation Manual Download Page 107

Serial port specifications (protocol)

Parameter

Value

Baud

9600 bps

Data bits

8

Parity

None

Stop bits

1

Flow control

None

Memory specifications

Memory

Type

Size

Boot

SPI Flash

2 x 8 MB

Compact Flash

NAND

2 GB

Main

DDR3 (onboard IC)

ICX 7250-24G: 1 GB

ICX 7250-24: 2 GB

ICX 7250-24P: 2 GB

ICX 7250-48: 2 GB

ICX 7250-48P: 2 GB

Regulatory compliance (EMC)

∙

FCC Part 15, Subpart B (Class A)

∙

EN 55022 (CE mark) (Class A)

∙

EN 55024 (CE mark) (Immunity) for Information Technology Equipment

∙

ICES-003 (Canada) (Class A)

∙

AS/NZ 55022 (Australia) (Class A)

∙

VCCI (Japan) (Class A)

∙

EN 61000-3-2

∙

EN 61000-3-3

∙

EN 61000-6-1

Regulatory compliance (safety)

∙

CAN/CSA-C22.2 No. 60950/UL 60950

∙

EN 60825 Safety of Laser Products

∙

EN 60950/IEC 60950 Safety of Information Technology Equipment

Regulatory compliance (environmental)

∙

2014/35/EU and 2014/30/EU

∙

2011/65/EU - Restriction of the use of certain hazardous substance in electrical and electronic equipment (EU RoHS).

 Brocade ICX 7250 Switch Technical Specifications

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

107

Summary of Contents for ICX 7250
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands