manualshive.com logo in svg

Brocade Communications Systems ICX 7250, Hardware Installation Manual

Share
Download
Brocade Communications Systems ICX 7250 Hardware Installation Manual Download Page 38

Attaching the front brackets to the rear of the device

NOTE
In this installation, the brackets are named as listed in the parts list even though the installation of the brackets is reversed from
the flush-front installation.

Complete the following steps to attach the front brackets to the rear of the device.

1.

Position the right front bracket with the flat side against the right rear side of the device, as shown in 

Figure 21

.

2. Insert four 8-32 x 5/16-in. flathead screws through the vertically aligned holes in the bracket and then into the holes on the side

of the device. Use the upper and lower screw holes, leaving the center holes empty.

3. Repeat 

Step 1

 and 

Step 2

 to attach the left rear bracket to the left side of the device.

4. Tighten all the 8-32 x 5/16-in. screws to a torque of 15 in-lb (17 cm-kg).

FIGURE 21 Attaching the front brackets to the rear of the device

1.

Device

2.

Screws, 8-32 x 5/16-in., flathead Phillips

3.

Front brackets

Installation

Brocade ICX 7250 Switch Hardware Installation Guide

38

53-1003898-02

Summary of Contents for ICX 7250
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands