manualshive.com logo in svg

Brocade Communications Systems ICX 7250 Stacking, Deployment Manual

Share
Download
Brocade Communications Systems ICX 7250 Stacking Deployment Manual Download Page 7

Flex module support in different slots

TABLE 1   

Part
Number

Ports

ICX7450-24

ICX7450-24 P

ICX7450-48

ICX7450-48P

ICX7450-48F

Module 2
Front

Module 3
Rear

Module 4
Rear

Module 2
Front

Module 3
Rear

Module 3
Rear

ICX7400-4X
1GF

4-port
100M/1G
SFP

Uplink

No

No

Uplink

No

No

ICX7400-4X
10GF

4-port
1/10G SFP
+

Uplink

Uplink

Uplink

Uplink

Uplink

Uplink

ICX7400-4X
10GC

4-port
1/10G
10GBaseT
Copper

Uplink

Uplink

Uplink

Uplink

Uplink

Uplink

ICX7400-1X
40GQ

1-port 40G
QSFP+

Uplink

Uplink or
stacking

Uplink or
stacking

No

Uplink or
stacking

Uplink or
stacking

ICX7450-24

This is a fixed 24-Port RJ45 10/100/1000Mbps Ethernet port platform and it is EEE hardware ready. It
has a full wide hot-plug module slot in the front and two full wide hot-plug module slots in the back.

ICX7450-24P

This is a fixed 24-Port RJ45 10/100/1000Mbps Ethernet port platform with EEE hardware ready and
PoE support. The SKU supports PoE (15.4 W) and PoE+ (25.5 W) on all the ports while Cisco's
proprietary uPoE (60W)and HDBase-T alliance's PoH (up to 95W) support is provided in the first eight
ports. It has full wide hot-plug module slot in the front and two full wide hot-plug module slots in the
back.

FIGURE 2

 ICX 7450-24P Front Panel

ICX7450-48

This is a fixed 48-Port RJ45 10/100/1000Mbps Ethernet port platform that is EEE hardware ready. It has
a full wide hot-plug module slot in the front and two full wide hot-plug module slots in the back.

ICX7450-48P

This is a fixed 48-Port RJ45 10/100/1000Mbps Ethernet port platform with EEE hardware ready and
PoE support. The SKU supports PoE (15.4 W) and PoE+ (25.5 W) on all the ports, while Cisco's
proprietary uPoE (60 W) and HDBase-T alliance's PoH (up to 95W) support is provided in the first eight
ports. It has full wide hot-plug module slot in the front and two full wide hot-plug module slots in the
back.

Brocade ICX 7450, Brocade ICX 7750, and Brocade ICX 7250 Stacking

Brocade ICX 7450, Brocade ICX 7750, and Brocade ICX 7250 Stacking Deployment Guide

7

53-1003581-03

Summary of Contents for ICX 7250 Stacking




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands