manualshive.com logo in svg

Brocade Communications Systems ICX 7250 Stacking, Deployment Manual

Share
Download
Brocade Communications Systems ICX 7250 Stacking Deployment Manual Download Page 69

Steps

Summarized steps:

• Configure 'stack enable' on the intended active controller unit at configuration level.
• Enter 'stack secure setup' on the intended active controller unit at device level.

Detailed Steps

1. Connect the units in a stack based on the connection guidelines. Select a unit that you want to

become an active controller. Configure 'stack enable' at configuration level as seen in the following
log.

ICX7250-24P Switch(config)#stack enable 

Enable stacking. This unit actively participates in stacking

stacking is enable. optical monitoring for stacking ports 1/2/1, 1/2/3 is not 

available.

ICX7250-24P Switch(config)#

2. Once stack enable configured, this command will configure two default stack ports 1/2/1 and 1/2/3 as

seen in the message displayed. This can be confirmed using 'show run' command. If you want to
connect stack units using the retimer ports (1/2/5 to 1/2/8), 'default-ports' command can be used to
change the default ports manually on the devices.

ICX7250-24P Switch(config)#stack unit 1

ICX7250-24P Switch(config-unit-1)#default-ports 1/2/5 1/2/7

3. Verify with show running-config that the default ports are set to 1/2/5 and 1/2/7.

ICX7250-24P Switch(config-unit-1)#show run 

Current configuration:

!

ver 08.0.30T211

!

stack unit 1

  module 1 icx7250-24p-poe-port-management-module

  module 2 icx7250-sfp-plus-8port-80g-module

  default-ports 1/2/5 1/2/7

4. Enter 'stack secure setup 'at device level. As shown in the following example, this command triggers

a Brocade proprietary discovery protocol that begins the discovery process in both upstream and
downstream directions. The discovery process produces a list of upstream and downstream devices
that are available to join the stack. This process will assign IDs to the units.

5. During stack formation you will be prompted to use the RING topology. If 'n' is selected, it prompts

you to enter the desired number of units either upstream or downstream depending on the
connections.

NOTE

During the secure-setup process, after one minute of inactivity, authentication for stack members
expires, forcing you to restart the process.

To exit the secure-setup, enter ^C at any time.

ICX7250-24P Switch#stack secure

ICX7250-24P Switch#Discovering the stack topology...

Current Discovered Topology - RING

Available UPSTREAM units

Hop(s)  Id      Type          Mac Address

 1       new  ICX7250-48P     cc4e.24b4.2eb0

 2       new  ICX7250-48P     cc4e.24b4.2f28

 3       new  ICX7250-24      cc4e.24b4.8988

 4       new  ICX7250-48      cc4e.24b4.2820

 5       new  ICX7250-48      cc4e.24b4.2514

 6       new  ICX7250-24      cc4e.24b4.83a0

 7       new  ICX7250-24      cc4e.24b4.8064

 8       new  ICX7250-24      cc4e.24b4.84c0

 9       new  ICX7250-24      cc4e.24b4.8670

10       new  ICX7250-24P     cc4e.24b4.7efc

11       new  ICX7250-24P     cc4e.24b4.7bc0

Available DOWNSTREAM units

Brocade ICX 7450, Brocade ICX 7750, and Brocade ICX 7250 Stacking

Brocade ICX 7450, Brocade ICX 7750, and Brocade ICX 7250 Stacking Deployment Guide

69

53-1003581-03

Summary of Contents for ICX 7250 Stacking




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands