manualshive.com logo in svg

Brocade Communications Systems ICX 7250 Stacking, Deployment Manual

Share
Download
Brocade Communications Systems ICX 7250 Stacking Deployment Manual Download Page 68

Unit # to Unit #

Link

Unit2 to Unit3

2/2/5 to 3/2/1

2/2/6 to 3/2/2

Bill of Materials

Products used in ICX 7250 stacking

TABLE 13   

Identifier

Vendor

Model

Notes

Switch/Units

Brocade

ICX7250-48P, ICX7250
-48, ICX7250 -24P and
ICX7250-24

Stack can be formed with mix
and match of all 4 different
SKUs listed

Stacking cable: Copper
option

Refer to 

Table 14

1,3, 5 active and
passive twinax

For each uplink and downlink 1
cable each.The numbers vary if
two port or three port stack
trunks are used.

Stacking cable: Fiber-
optic options

Refer to 

Table 14

10G-USR, 10G-SR,
10G-LR

Fiber optic maximum distance is
10 KM

Applicable Image

FastIron Release 08.0.30
or a later release

NA

All units should have same
software image

License needed for
stacking

Brocade

All

2 port or 8 port License

Optics information for ICX 7250 stacking

TABLE 14   

SFP+ Hardware

Description

BRCD Part Number

10G Active Twinax 1m (SFP +)

10G Active Twinax 1m

58-1000026-01

10G Active Twinax 3m (SFP +)

10G Active Twinax 3m

58-1000027-01

10G Active Twinax 5m (SFP +)

10G Active Twinax 5m

58-1000023-01

10GE LR 10km (SFP +)

10GE LR 10km (SFP +)

57-0000076-01

10GE LSR 300m (SFP +)

10GE SR 300m (SFP +)

57-0000075-01

10GE USR 100m (SFP +)

10GE LR 10km (SFP +)

57-1000130-01

NOTE

7M active cables are not supported for stacking with ICX 7250.

Stack formation method 1: Using stack secure setup

Description

'Stack secure setup' utility is the most convenient of all methods to form a stack. This utility uses a
Brocade proprietary discovery protocol that discovers units that are connected upstream and
downstream of the unit where this command is entered.

Stack formation method 1: Using stack secure setup

68

Brocade ICX 7450, Brocade ICX 7750, and Brocade ICX 7250 Stacking Deployment Guide

53-1003581-03

Summary of Contents for ICX 7250 Stacking




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands