manualshive.com logo in svg

Brocade Communications Systems ICX 7250 Stacking, Deployment Manual

Share
Download
Brocade Communications Systems ICX 7250 Stacking Deployment Manual Download Page 14

Optics information for the Brocade ICX7450 stacking (Continued)

TABLE 3   

QSFP Hardware

Description

BRCD Part Number

40G-QSFP-LR4

40GE LR

57-1000263-01

40G-QSFP-LR4

40GE LR

57-1000263-01

40G-QSFP-C-00501

40GE QSFP to QSFP 0.5M
Cable(Passive)

58-0000056-01

40G-QSFP-C-00501

40GE QSFP to QSFP 0.5M
Cable(Passive)

58-0000056-01

40G-QSFP-C-00501

40GE QSFP to QSFP 0.5M
Cable(Passive)

58-0000056-01

40G-QSFP-C-0101

40GE QSFP to QSFP 1M
Cable(Passive)

58-0000033-01

40G-QSFP-C-0101

40GE QSFP to QSFP 1M
Cable(Passive)

58-0000033-01

40G-QSFP-QSFP-C-0101

40GE QSFP Active Copper 1m

58-0000041-01

40G-QSFP-QSFP-C-0101

40GE QSFP Active Copper 1m

58-0000041-01

40G-QSFP-QSFP-C-0301

40GE QSFP Active Copper 3m

58-0000042-01

40G-QSFP-QSFP-C-0301

40GE QSFP Active Copper 3m

58-0000042-01

40G-QSFP-QSFP-C-0501

40GE QSFP Active Copper 5m

58-0000043-01

40G-QSFP-QSFP-C-0501

40GE QSFP Active Copper 5m

58-0000043-01

Stack construction method 1: Stack secure setup

Description

'Stack secure setup' utility is the most convenient of all methods to form a stack. This utility uses a
Brocade proprietary discovery protocol that discovers units that are connected upstream and
downstream from the switch where this command is entered, the intended Active controller.

Steps

Stack formation with secure setup utility:

• Configure 'stack enable' on the intended active controller unit at configuration level.
• Enter 'stack secure setup' on the intended active controller unit at device level.

Detailed steps:

1. Select a unit that you want to become an active controller. Configure 'stack enable' at configuration

level as seen in the following logs.

ICX7450-24 Router#configure terminal

ICX7450-24 Router(config)#

stack enable

Enable stacking. This unit actively participates in stacking

stacking is enable. optical monitoring for stacking ports 1/3/1, 1/4/1 is not 

available.

ICX7450-24 Router(config)#

2. Once stack enable is configured, this command will configure two default stack ports, 1/3/1 and

1/4/1 as seen in the message displayed. This can be confirmed using 'show run' command.

ICX7450-24 Switch(config)#show running

Current configuration:

!

ver 08.0.20T213

Stack construction method 1: Stack secure setup

14

Brocade ICX 7450, Brocade ICX 7750, and Brocade ICX 7250 Stacking Deployment Guide

53-1003581-03

Summary of Contents for ICX 7250 Stacking




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands