manualshive.com logo in svg

Brocade Communications Systems ICX 7250 Stacking, Deployment Manual

Share
Download
Brocade Communications Systems ICX 7250 Stacking Deployment Manual Download Page 54

show stack neighbors

Enter the

 show stack neighbors

 command at the device level. This command displays neighboring

units for each stack port. . In case when a unit turns bad this output is useful to debug the neighboring
units are detected or not.

ICX7750-48F Router# 

show stack neighbors

 U#  Stack-port1                                  Stack-port2            

1   (1/2/1)                                   (1/2/4)             

2   (2/2/1)                                   (2/2/4)             

3   (3/2/1)                                   (3/2/4)             

4   (4/2/1-4/2/3)                             (4/2/4)             

5   (5/2/1)                                   (5/2/4-5/2/6)       

6   (6/2/1-6/2/3)                             (6/2/4)             

7   (7/2/1)                                   (7/2/4-7/2/6)       

8   (8/2/1)                                   (8/2/4)             

9   (9/2/1)                                   (9/2/4)             

10  (10/2/1-10/2/2)                           (10/2/4)            

11  11/2/1-11/2/2)                            (11/2/4-11/2/5)     

12  (12/2/1)                                  (12/2/4-12/2/5)    

show stack connections

Enter the 

show stack connection

 command at the device level. This command displays total

stacking links on the topology along with stack port 1(P0) and stack port 2(P1) for each stacking link. It
also displays CPU to CPU packets are fine between the units. If the stack ports link goes down, this
output helps debug if the neighboring links are detected or not.

ICX7750-48F Switch# 

show stack connection 

Probing the topology. Please wait ...

ICX7750-48F Switch#

    active                                                                     

     +---+        +---+        +---+        +---+        +---+        +---+    

 -2/1| 1 |2/4--2/1| C |2/4==2/1| B |2/4==2/1| A |2/4--2/1| 9 |2/4--2/1| 8 |2/4-

 |   +---+        +---+        +---+        +---+        +---+        +---+   |

 |                                                                            |

 |  standby                                                                   |

 |   +---+        +---+        +---+        +---+        +---+        +---+   |

 -2/4| 2 |2/1--2/4| 3 |2/1--2/4| 4 |2/1==2/4| 5 |2/1--2/4| 6 |2/1==2/4| 7 |2/1-

     +---+        +---+        +---+        +---+        +---+        +---+   

trunk probe results: 12 links

Link 1: u1 -- u2, num=1

  1: 1/2/1 (P0) <---> 2/2/4 (P1)   

Link 2: u1 -- u12, num=1

  1: 1/2/4 (P1) <---> 12/2/1 (P0)   

Link 3: u2 -- u3, num=1

  1: 2/2/1 (P0) <---> 3/2/4 (P1)   

Link 4: u3 -- u4, num=1

  1: 3/2/1 (P0) <---> 4/2/4 (P1)   

Link 5: u4 -- u5, num=3

  1: 4/2/1 (T0) <---> 5/2/4 (T1)   

  2: 4/2/2 (T0) <---> 5/2/5 (T1)   

  3: 4/2/3 (T0) <---> 5/2/6 (T1)   

Link 6: u5 -- u6, num=1

  1: 5/2/1 (P0) <---> 6/2/4 (P1)   

Link 7: u6 -- u7, num=3

  1: 6/2/1 (T0) <---> 7/2/4 (T1)   

  2: 6/2/2 (T0) <---> 7/2/5 (T1)   

  3: 6/2/3 (T0) <---> 7/2/6 (T1)   

Link 8: u7 -- u8, num=1

  1: 7/2/1 (P0) <---> 8/2/4 (P1)   

Link 9: u8 -- u9, num=1

show stack neighbors

54

Brocade ICX 7450, Brocade ICX 7750, and Brocade ICX 7250 Stacking Deployment Guide

53-1003581-03

Summary of Contents for ICX 7250 Stacking




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands