manualshive.com logo in svg

Brocade Communications Systems ICX 7250 Stacking, Deployment Manual

Share
Download
Brocade Communications Systems ICX 7250 Stacking Deployment Manual Download Page 18

• Configure 'stack suggested-id' on the units that will have a desired ID.
• Configure 'stack enable' on all the units and connect the units using stack ports.

Detailed steps

1. Units should boot up using the same software image.
2. On the unit that is intended to be the active controller, configure priority 255. On the unit intended to

be on standby, configure priority 240. User can choose to have the same priority for active and
standby, which is useful in case of failover.

3. Since each unit is a clean unit, its unit id is 1. Enter 'configure terminal', enter 'stack unit 1' and

configure 'stack suggested-id' on all the units that will have the desired ID.

4. Configure 'stack enable' on all the units.

UNIT 1

:

ICX7450-24 Router(config)#

stack unit 1

ICX7450-24 Router(config-unit-1)#

priority 255

ICX7450-24 Router(config-unit-1)#

stack enable

Enable stacking. This unit actively participates in stacking

stacking is enable. optical monitoring for stacking ports 1/3/1, 1/4/1 is not 

available.

ICX7450-24 Router(config-unit-1)#

UNIT 2:

ICX7450-48 Router(config)#stack unit 1

ICX7450-48 Router(config-unit-1)#priority 240

ICX7450-48 Router(config-unit-1)#stack suggested-id 2

ICX7450-48 Router(config-unit-1)#stack enable

Enable stacking. This unit actively participates in stacking

stacking is enable. optical monitoring for stacking ports 1/3/1, 1/4/1 is not 

available.

ICX7450-48 Router(config-unit-1)#

UNIT 3:

ICX7450-48 Router(config-unit-1)#stack suggested-id 3

ICX7450-48 Router(config-unit-1)#stack enable

Enable stacking. This unit actively participates in stacking

stacking is enable. optical monitoring for stacking ports 1/3/1, 1/4/1 is not 

available.

ICX7450-48 Router(config-unit-1)#

UNIT 4:

ICX7450-48 Router(config)#stack unit 1

ICX7450-48 Router(config-unit-1)#stack suggested-id 4

ICX7450-48 Router(config-unit-1)#stack enable

Enable stacking. This unit actively participates in stacking

stacking is enable. optical monitoring for stacking ports 1/3/1, 1/4/1 is not 

available.

ICX7450-48 Router(config-unit-1)#

UNIT 5

ICX7450-48P Router(config)#stack unit 1

ICX7450-48P Router(config-unit-1)#stack suggested-id 5

ICX7450-48P Router(config-unit-1)#stack enable

Enable stacking. This unit actively participates in stacking

stacking is enable. optical monitoring for stacking ports 1/3/1, 1/4/1 is not 

available.

ICX7450-48P Router(config-unit-1)#

UNIT 6:

ICX7450-48F Router(config)#stack unit 1

ICX7450-48F Router(config-unit-1)#stack suggested-id 6

ICX7450-48F Router(config-unit-1)#stack enable

Enable stacking. This unit actively participates in stacking

stacking is enable. optical monitoring for stacking ports 1/3/1, 1/4/1 is not 

available.

ICX7450-48F Router(config-unit-1)#

UNIT 7:

ICX7450-48P Router(config)#stack unit 1

Brocade ICX 7450, Brocade ICX 7750, and Brocade ICX 7250 Stacking

18

Brocade ICX 7450, Brocade ICX 7750, and Brocade ICX 7250 Stacking Deployment Guide

53-1003581-03

Summary of Contents for ICX 7250 Stacking




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands