Brocade Communications Systems ICX 7250 Stacking Deployment Manual Download Page 22

Page: 22 / 83

• Configure 'default-ports 1/2/1 1/2/3' on all the units, write memory and reload. This step is needed

because mac-sec and stacking cannot exist at the same time on a port.

• When units boot up, configure 'stack enable' on the intended active controller unit at configuration

level.

• Enter 'stack secure setup' on the intended active controller unit at device level.

Detailed Steps

1. Select a unit that you want to become an active controller. Configure 'default-ports 1/2/1 1/2/3' on all

the units, write memory and reload

ICX7450-24 Router>enable

No password has been assigned yet...

ICX7450-24 Router#con t

ICX7450-24 Router(config)#stack unit 1

ICX7450-24 Router(config-unit-1)#default-ports 1/2/1 1/2/3

Reload required. Please write memory and then reload or power cycle.

ICX7450-24 Router(config-unit-1)#

ICX7450-24 Router(config-unit-1)#end

ICX7450-24 Router#

ICX7450-24 Router#Flash Memory Write (8192 bytes per dot) .

Write startup-config done.

Copy Done.

ICX7450-24 Router#

ICX7450-24 Router#rel

Sent SIGTERM to all processesn'):

Sent SIGKILL to all processes

Requesting system reboot

Restarting system.

2. When units boot up, show run will show default ports configured as 1/2/1 1/3/1. Configure 'stack

enable' on the intended active unit.

ICX7450-24 Router#show run

Current configuration:

ver 08.0.30q101T213

stack unit 1

module 1 icx7450-24-port-management-module

module 2 icx7400-xgf-4port-40g-module

module 3 icx7400-xgf-4port-40g-module

module 4 icx7400-qsfp-1port-40g-module

default-ports 1/2/1 1/2/3

--More--, next page: Space, next line: Return key, quit: Control-c^C

ICX7450-24 Router#configure terminal

ICX7450-24 Router(config)#stack enable

Enable stacking. This unit actively participates in stacking

stacking is enable. optical monitoring for stacking ports 1/2/1, 1/2/3 is not

available.

ICX7450-24 Router(config)#

3. Run the 'stack secure setup' utility on the intended active unit. Since ports are connected to form

trunks, user is prompted to make a selection for desired links, enter 2 for trunks. In the following
example 11 units are discovered during stack secure setup.

ICX7450-24 Router(config)#show run

Current configuration:

ver 08.0.30q101T213

stack unit 1

module 1 icx7450-24-port-management-module

module 2 icx7400-xgf-4port-40g-module

module 3 icx7400-xgf-4port-40g-module

module 4 icx7400-qsfp-1port-40g-module

default-ports 1/2/1 1/2/3

--More--, next page: Space, next line: Return key, quit: Control-c^C

ICX7450-24 Router(config)#exit

ICX7450-24 Router#stack secure-setup

ICX7450-24 Router#Discovering the stack topology...

Brocade ICX 7450, Brocade ICX 7750, and Brocade ICX 7250 Stacking

Brocade ICX 7450, Brocade ICX 7750, and Brocade ICX 7250 Stacking Deployment Guide

53-1003581-03

Summary of Contents for ICX 7250 Stacking




















































































Search results

Summary of Contents for ICX 7250 Stacking

Reviews:

Brands by name

Popular brands

Brocade Communications Systems ICX 7250 Stacking, Deployment Manual

Search results

Summary of Contents for ICX 7250 Stacking

Reviews:

Brands by name

Popular brands