manualshive.com logo in svg

Broadcom NetXtreme/NetLink BCM5717, Programmer'S Manual

The Broadcom NetXtreme/NetLink BCM5717 Programmer's Manual is a comprehensive guide for users looking to maximize the functionality of their network adapter. This manual provides detailed instructions on installation, configuration, and troubleshooting. Download this manual for free from manualshive.com to get the most out of your BCM5717.

Share
Download
background image

Expansion ROM

BCM5718 Programmer’s Guide

 

Broadcom

®

 

January 29, 2016 • 5718-PG108-R

Page 187

Operational Characteristics

Read/Write DMA Engines

Software must enable the bus master DMA bit for the Ethernet controller. The Ethernet controller is a bus-
mastering device and the PCI interface requires that the Bus_Master enable bit be set by either the BIOS or 
host device driver. The bus master is the PCI transaction initiator. A PCI target will claim the transaction driven 
by the bus master. The Bus_Master enable bit is located in the PCI configuration space Command register and 
this bit is read/write. The bit defaults to cleared/disabled after device reset. 

The read and write DMA channels use FIFOs to buffer small amounts of PCI bus data. The FIFOs provide 
elasticity for data movement between internal memory and the PCI interface. Host software may configure DMA 
watermarks—values where PCI activity is enabled/disabled.

When enqueued data is less than the watermark value, PCI bus transactions are inhibited. The DMA channel 
will wait until the FIFO fills above the threshold before initiating PCI transactions. Host software may configure 
the DMA_Write_Watermark bit fields to set the activity threshold in the write FIFO. The DMA_Write_Watermark 
bit field is read/write and is also located in the DMA Read/Write register. The write watermark registers default 
to zero after power-on reset.

Expansion ROM

Description

The expansion ROM on the Ethernet controller is intended for implementation of PXE (Preboot Execution 
Environment). The devices support expansion ROM of up to 16 MB.

Operational Characteristics

By default, the Expansion ROM is disabled and the firmware has to explicitly enable this feature by setting 
PCI_State.PCI_Expansion_ROM_Desired bit to one (see 

“PCI State Register (offset: 0x70)” on page 285

). 

Once this bit is enabled, the boot code firmware handles the Expansion ROM accesses of the device.

BIOS

The BIOS detects if a PCI device supports Expansion ROM or not by writing the value 0xFFFFFFFE to 
Expansion_ROM_Base_Register (register 0x30 of PCI configuration). The BIOS then reads back from this 
register. If the value is nonzero, then this PCI device supports Expansion ROM; otherwise, it does not. The 
Ethernet controller returns a nonzero value appropriate for the expansion ROM size selected in NVRAM (see 

Section 4: “Common Data Structures,” on page 69

) when Expansion ROM is enabled 

(PCI_State.PCI_Expansion_ROM_Desired bit is set to 1). On the other hand, if the 
PCI_Expansion_ROM_Desired bit cleared, then the Ethernet controller returns a value of 0x00000000. This 
indicates to the BIOS that no Expansion ROM is supported.

Summary of Contents for NetXtreme/NetLink BCM5717


















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NetXtreme/NetLink BCM5717

Eaton S611 User Manual preview
S611
Brand: Eaton Pages: 96
National Instruments SCXI -1122 Calibration Procedure preview
SCXI -1122
Brand: National Instruments Pages: 17
Davey Torrium 2 TT45 Installation And Operating Instructions Manual preview
Torrium 2 TT45
Brand: Davey Pages: 12
NEC uPD78F4225Y Manual preview
uPD78F4225Y
Brand: NEC Pages: 30
BQT BioX Series Installation Manual preview
BioX Series
Brand: BQT Pages: 2
Leggett & Platt G-SMR-2 CUSTOM Operation Manual preview
G-SMR-2 CUSTOM
Brand: Leggett & Platt Pages: 20
National Instruments cRIO-9064 User Manual preview
cRIO-9064
Brand: National Instruments Pages: 26
Phoenix Contact FL EPA 2 User Manual preview
FL EPA 2
Brand: Phoenix Contact Pages: 40
Pentair FLECK 5810 XTR2 Service Manual preview
FLECK 5810 XTR2
Brand: Pentair Pages: 36
zeeltronic PDCI-24V User Manual preview
PDCI-24V
Brand: zeeltronic Pages: 13
QD Dynamics Pi HSC505-32 User'S Information Manual preview
Pi HSC505-32
Brand: QD Dynamics Pages: 64
Velleman CHLSC2 User Manual preview
CHLSC2
Brand: Velleman Pages: 22
National Instruments NI 9683 User Manual And Specifications preview
NI 9683
Brand: National Instruments Pages: 27
SPXFLOW Bilge Pump Control Panel Instruction Manual preview
Bilge Pump Control Panel
Brand: SPXFLOW Pages: 14
Zamel EXTA LIFE P-520 Manual preview
EXTA LIFE P-520
Brand: Zamel Pages: 10
Black Box ServLink ACR3500A Manual preview
ServLink ACR3500A
Brand: Black Box Pages: 115
LS Industrial Systems GLOFA G7M-DR20U User Manual preview
GLOFA G7M-DR20U
Brand: LS Industrial Systems Pages: 367
MIT TRG-BS-12 User Manual preview
TRG-BS-12
Brand: MIT Pages: 20

Brands by name

Popular brands

Load more brands