manualshive.com logo in svg

Broadcom NetXtreme/NetLink BCM5717, Programmer'S Manual

The Broadcom NetXtreme/NetLink BCM5717 Programmer's Manual is a comprehensive guide for users looking to maximize the functionality of their network adapter. This manual provides detailed instructions on installation, configuration, and troubleshooting. Download this manual for free from manualshive.com to get the most out of your BCM5717.

Share
Download
background image

Host Coalescing Control Registers

BCM5718 Programmer’s Guide

 

Broadcom

®

 

January 29, 2016 • 5718-PG108-R

Page 421

HC Parameter Set Reset Register (Offset: 0x3C28)

Place this in HC block.

Status Block Host Address Register (offset: 0x3C38)

This 64-bit register is in host address format and tells the NIC where to DMA the status block.

When IOV is enabled:

Status Block 0 Host Address Register (offset: 0x3C38)

Status Block 1 Host Address Register (offset: 0x3D00)

Status Block 2 Host Address Register (offset: 0x3D08)

Status Block 3 Host Address Register (offset: 0x3D10)

Status Block 4 Host Address Register (offset: 0x3D18)

Status Block 5 Host Address Register (offset: 0x3D20)

Status Block 6 Host Address Register (offset: 0x3D28)

Status Block 7 Host Address Register (offset: 0x3D30)

Status Block 8 Host Address Register (offset: 0x3D38)

Status Block 9 Host Address Register (offset: 0x3D40)

Status Block 10 Host Address Register (offset: 0x3D48)

Status Block 11 Host Address Register (offset: 0x3D50)

Status Block 12 Host Address Register (offset: 0x3D58)

Status Block 13 Host Address Register (offset: 0x3D60)

Status Block 14 Host Address Register (offset: 0x3D68)

Status Block 15 Host Address Register (offset: 0x3D70)

Table 107:  HC Parameter Set Reset Register (Offset: 0x3C28)

Name

Bits

Access

Default 
Value

Description

Legacy

31:17 RU

0x0

Unused

HC Parameter Set Reset 

Bit-Map

16:0

RW

0x0

Write a 1 to the position of this bit map to clear the 

respective HC Parameter Register Set – the 

associated internal HC states are also cleared by 

this action.
This is useful for VRQ Flush-Synch purposes 

while in IOV Mode. 

Summary of Contents for NetXtreme/NetLink BCM5717


















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NetXtreme/NetLink BCM5717

ABB FDNA-01 Quick Installation And Start-Up Manual preview
FDNA-01
Brand: ABB Pages: 2
Parasound 7100 Owner'S Manual preview
7100
Brand: Parasound Pages: 72
Jafar 7010 Operation And Maintenance Manual preview
7010
Brand: Jafar Pages: 15
Canon imageRUNNER ADVANCE C9075S PRO User Manual preview
imageRUNNER ADVANCE C9075S PRO
Brand: Canon Pages: 20
NEJE E80 Manual preview
E80
Brand: NEJE Pages: 17
Oceanic ZX Service Procedure preview
ZX
Brand: Oceanic Pages: 13
VADDIO EVI-D70 Installation And User Manual preview
EVI-D70
Brand: VADDIO Pages: 2
IBM 1620 Manual Of Instruction preview
1620
Brand: IBM Pages: 12
K&K M9700 Installation Instructions Manual preview
M9700
Brand: K&K Pages: 10
YASKAWA PROFINET V1000 Technical Manual preview
PROFINET V1000
Brand: YASKAWA Pages: 49
M-system MSP10 Instruction Manual preview
MSP10
Brand: M-system Pages: 17
Samson 3756 Mounting And Operating Instructions preview
3756
Brand: Samson Pages: 56
EasyIO FG-20 Installation Manual preview
FG-20
Brand: EasyIO Pages: 17
M-system R3-PD16B Instruction Manual preview
R3-PD16B
Brand: M-system Pages: 10
Eaton Cutler-Hammer LMR Instructions Manual preview
Cutler-Hammer LMR
Brand: Eaton Pages: 38
Moeller F&G Xcomfort CRCA-00/02 Assembly Instructions preview
F&G Xcomfort CRCA-00/02
Brand: Moeller Pages: 4
Automated Logic UNI/32 Technical Instructions preview
UNI/32
Brand: Automated Logic Pages: 10
Objective Imaging OASIS-4i Installation Manual preview
OASIS-4i
Brand: Objective Imaging Pages: 11

Brands by name

Popular brands

Load more brands