manualshive.com logo in svg

Broadcom NetXtreme/NetLink BCM5717, Programmer'S Manual

The Broadcom NetXtreme/NetLink BCM5717 Programmer's Manual is a comprehensive guide for users looking to maximize the functionality of their network adapter. This manual provides detailed instructions on installation, configuration, and troubleshooting. Download this manual for free from manualshive.com to get the most out of your BCM5717.

Share
Download
background image

Endian Control (Byte and Word Swapping)

BCM5718 Programmer’s Guide

 

Broadcom

®

 

January 29, 2016 • 5718-PG108-R

Page 194

Architecture

The Ethernet controller is internally a big-endian machine, and its internal processors are big-endian devices. 
The Ethernet controller stores data internally in big-endian format using a 64-bit memory subsystem. 

However, many hosts (e.g., x86 systems) use the little-endian format, and the PCI bus uses the little-endian 
format. Therefore the Ethernet controller has a number of byte swapping options that may be configured by 
software so that Little or Big Endian hosts can interface as seamlessly as possible with Ethernet controller over 
PCI. The Ethernet controller has the following bits that control byte and word swapping:

• Enable Endian Word Swap (bit 3, Miscellaneous Host Control register (offset 0x68 into PCI Config register, 

se 

“Miscellaneous Host Control Register (offset: 0x68)” on page 282

). If 1, this register enables 32-bit word 

swapping when accessing the Ethernet controller via the PCI target interface.

• Enable Endian Byte Swap (bit 2, Miscellaneous Host Control register (offset 0x68 into PCI Config register, 

see 

“Miscellaneous Host Control Register (offset: 0x68)” on page 282

). If 1, this register enables byte 

swapping (within a 32-bit word) when accessing the Ethernet controller via the PCI target interface.

• Word Swap Data (bit 5, Mode Control register (offset 0x6800 into the Ethernet controller registers). If 1, this 

register enables word swapping of frame data when it comes across the bus.

• Byte Swap Data (bit 4, Mode Control register (offset 0x6800 into the Ethernet controller registers). If 1, this 

register enables byte swapping of frame data when it comes across the bus.

• Word Swap Non-Frame Data (bit 2, Mode Control register (offset 0x6800 into the Ethernet controller 

registers). If 1, this register enables word swapping of non frame data (i.e., buffer descriptors, statistics, 
etc.) when it comes across the bus.

• Byte Swap Non-Frame Data (bit 1, Mode Control register (offset 0x6800 into the Ethernet controller 

registers). If 1, this register enables byte swapping of non frame data (i.e., buffer descriptors, statistics, etc.) 
when it comes across the 

bus

.

The setting of the above swapping bits will affect the order of how data is represented when it is transferred 
across PCI. Since byte swapping is a confusing subject, examples will be shown that reflect how each byte 
swapping bit works.

Enable Endian Word Swap and Enable Endian Byte Swap Bits

The Enable Endian Word Swap, and Enable Endian Byte Swap bits affect whether words or bytes are swapped 
during target PCI accesses. Thus, these bits affect the byte order when the host is directly reading/writing to 
registers or control structures that are physically located on the Ethernet controller. These bits do not affect the 
byte ordering of packet data or other structures that are mastered (DMAed) by the Ethernet controller.

When the Ethernet controller is accessed via PCI (which is little endian) as a PCI target, the Ethernet controller 
must implicitly map those accesses to internal structures that use a 64-bit Big Endian architecture. In the default 
case where no swap bits are set the Ethernet controller maps PCI data to internal structures shown in 

Table 54

 

and 

Table 55 on page 195

. 

Table 54:  Default Translation (No Swapping) on 64-Bit PCI

MSB

LSB

Internal Byte #

0

1

2

3

4

5

6

7

Internal Bit #

63

47

31

15

Summary of Contents for NetXtreme/NetLink BCM5717


















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NetXtreme/NetLink BCM5717

GE RSTi-EP User Manual preview
RSTi-EP
Brand: GE Pages: 425
ZETRON MAX Connection Manual preview
MAX
Brand: ZETRON Pages: 3
ADEMCO MAX Programming Instructions preview
MAX
Brand: ADEMCO Pages: 2
Access Flow2 User'S Manual & Installation Instructions preview
Flow2
Brand: Access Pages: 12
Bang & Olufsen BeoSystem 4 How To Use Manual preview
BeoSystem 4
Brand: Bang & Olufsen Pages: 36
Mad Catz DVD 2 Owner'S Manual preview
DVD 2
Brand: Mad Catz Pages: 4
Parker CHELSEA Owner'S Manual preview
CHELSEA
Brand: Parker Pages: 32
Rayrun NT30 Quick Start Manual preview
NT30
Brand: Rayrun Pages: 4
PACH & COMPANY AeGIS 7000 Series Quick Start Manual preview
AeGIS 7000 Series
Brand: PACH & COMPANY Pages: 2
Talgil DREAM 2 Manual preview
DREAM 2
Brand: Talgil Pages: 14
Tadao Musashi 3 Upgrade preview
Musashi 3
Brand: Tadao Pages: 2
Watlow F4T Quick Start Manual preview
F4T
Brand: Watlow Pages: 4
Z3 Technology Z3-DM8107-SDI-RPS User Manual preview
Z3-DM8107-SDI-RPS
Brand: Z3 Technology Pages: 73
Z-Wave Control4 Setup Manual preview
Control4
Brand: Z-Wave Pages: 14
Z-Wave.Me KFOB2 Quick Start preview
KFOB2
Brand: Z-Wave.Me Pages: 4
Osram OT EASY 32 CC Fitting Instructions preview
OT EASY 32 CC
Brand: Osram Pages: 3
Baier 50VA Instruction Manual preview
50VA
Brand: Baier Pages: 20
Carrier AQUASNAP 30RA "B" Operation & Maintenance Instructions Manual preview
AQUASNAP 30RA "B"
Brand: Carrier Pages: 36

Brands by name

Popular brands

Load more brands