Broadcom NetXtreme/NetLink BCM5717 Programmer'S Manual Download Page 87 | Manualshive

Page: 87 / 593

background image

Status Block

BCM5718 Programmer’s Guide

Broadcom

®

January 29, 2016 • 5718-PG108-R

Page 87

The Status Block format for these devices is as follows:

• Status Tag—Contains an unique eight-bit tag value in bits 7:0 when the Status Tagged Status mode bit of

the Miscellaneous Host Control register (see

“Miscellaneous Host Control Register (offset: 0x68)” on

) is set to 1. This Status Tag can be returned to the Mailbox 0 register at location 31:24

(see

“Interrupt Mailbox 0 Register (offset: 0x5800)” on page 460

) by host driver. When the remaining

Mailbox 0 register bits 23:0 are written as 0, the tag field of the Mailbox 0 register is compared with the tag
field of the last status block to be DMAed to host. If the tag returned is not equivalent to the tag of the last
status block DMAed to the host, the interrupt state is entered.

• Receive Producer Ring Consumer Index—Contains the controller’s current Consumer Index value for the

Receive Producer Ring. This field indicates how many receive descriptors are in the receive producer ring
that the controller has consumed. For more information regarding this ring, see

“Receive Producer Ring” on

.

• Receive Return Rings 0–3 Producer Indices—Contain controller’s current Producer Index value for the

each of the Receive Return Rings. When the controller receives a packet and writes that packet data into
host memory via DMA, it will increment the Producer Index for the corresponding Receive Return ring.
When a Producer Index is incremented, it is a signal to software that a newly arrived receive packet is
ready to be processed.

• Send Ring Consumer Index—Contains controller’s current Consumer Index value for the Send Ring.

When the controller completes the read DMA of the host buffer associated with a send BD, the controller
will update the Send Ring Consumer Index. This provides the host software with an indication that the
controller has buffered this send data and, therefore, the host software may free the buffer that was just
consumed by the device.

1

Link State Changed

Indicates that link status has changed. This method of determining link change

status provides a small performance increase over doing a PIO read of the

Ethernet MAC Status register (see

“EMAC Status Register (offset: 0x404)” on

. See

“Wake on LAN Mode/Low-Power” on page 212

for a description

of the PHY setup required when link state changes.

2

Error

When this bit is asserted by the chip, the following conditions may have

occurred. Bit 2 of the status word is the OR of:

• All bits in Flow Attention register (0x3c48) (see

“Flow Attention Register

(offset: 0x3C48)” on page 422

• MAC_ATTN—Events from the MAC block (see

“EMAC Status Register

(offset: 0x404)” on page 311

• DMA_EVENT—Events from the following blocks:

– MSI (see

“MSI Status Register (offset: 0x6004)” on page 467

.

– DMA_RD (see

“LSO Read DMA Status Register (offset: 0x4804)” on

– DMA_WR (see

“Write DMA Status Register (offset: 0x4C04)” on

• RXCP_ATTN—Events from RX RISC (see

“RX RISC Status Register (offset:

0x5004)” on page 452

.

Table 19: Status Word Flags (Cont.)

Bits

Name

Description

«
...
85
86
87
88
89
...
»

Summary of Contents for NetXtreme/NetLink BCM5717


















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NetXtreme/NetLink BCM5717

Brand: Baby Trend Pages: 8

Brand: Baby Trend Pages: 19

Brand: Baby Trend Pages: 5

Brand: Baby Trend Pages: 4

Brand: L. G. B. Pages: 2

Brand: L-Acoustics Pages: 36

Brand: Baier Pages: 20

LOWARA Aquavara IPC

Brand: Xylem Pages: 292

Brand: Euromatic Pages: 20

Brand: VMK Pages: 98

AQUIS ULTRAFLOW

Brand: Waterous Pages: 217

Brand: Harman Pages: 2

Brand: Linear Technology Pages: 6

Brand: Nortek Pages: 24

Brand: Kong Pages: 2

Easywave ST01 Series

Brand: Eldat Pages: 2

Brand: u-blox Pages: 157

Brand: Airlow Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands