Broadcom NetXtreme/NetLink BCM5717 Programmer'S Manual Download Page 273

Page: 273 / 593

PCI Configuration Registers

BCM5718 Programmer’s Guide

Broadcom

January 29, 2016 • 5718-PG108-R

Page 273

PCI Classcode and Revision ID Register (offset: 0x08)

This register is reset by Hard Reset.

BIST, Header Type, Latency Timer, Cache Line Size Register (offset:
0x0C)

Name

Bits

Access

Default
Value

Description

PCI Classcode

31:8

0x020000

Default for (LAN Function 0): 0x020000

Revision ID—All-

layer Revision ID

7:4

ASIC Rev

Input

This field will be updated automatically by hardware

based on the External All Layer Revision ID. For

example, this field will contain a value of 0x0 after hard

reset for BCM5718 A0 silicon. Software shall use this

field only to display the Device Silicon Revision ID for

application where the user/customer needs to know the

Device Silicon Revision ID. One such application is the

B57DIAG Device Banner. Furthermore, Software (Boot

Code/Driver/B57DIAG) shall NOT use this field in

determining Bug Fixes. It should only use the Internal

Revision ID, bits 31:24 and bits 19:16 from Register 68,

for that purpose.

• 0x0 for A steps
• 0x1 for B steps
• 0x2 for C steps

Revision ID —

Metal Revision ID

3:0

FW-RW
Host-RO

ASIC Rev

Input

This field will be updated automatically by hardware

based on the Metal Revision ID.

• 0x0 for metal 0 step
• 0x1 for metal 1 step
• 0x2 for metal 2 step

Name

Bits

Access

Default
Value

Description

BIST

31:24

0x0

The 8-bit BIST register is used to initiate and report the

results of any Built-In-Self-Test. This value can be

written by firmware through the PCI register space BIST

Header Type

23:16

0x80

The 8-bit Header Type register identifies both the layout

of bytes 10h through 3Fh of the Configuration space, as

well as whether this adapter contains multiple functions.

A value of 0x80 indicates a multifunction device (Type

0) using the format specified in the PCI specification,

while a value of 0x0 indicates a single function Type 0

device.

Latency Timer

15:8

0x0

This register does not apply to PCI express and must

be hardwired to zero

Cache Line Size

7:0

0x0

This field is implemented by PCIE device as a read/

write field for legacy compatibility purposes.

Summary of Contents for NetXtreme/NetLink BCM5717


















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for NetXtreme/NetLink BCM5717

Reviews:

Related manuals for NetXtreme/NetLink BCM5717

Brands by name

Popular brands

Broadcom NetXtreme/NetLink BCM5717, Programmer'S Manual

Search results

Summary of Contents for NetXtreme/NetLink BCM5717

Reviews:

Related manuals for NetXtreme/NetLink BCM5717

Brands by name

Popular brands