Broadcom NetXtreme/NetLink BCM5717 Programmer'S Manual Download Page 172 | Manualshive

Page: 172 / 593

background image

Configuration Space

BCM5718 Programmer’s Guide

Broadcom

®

January 29, 2016 • 5718-PG108-R

Page 172

The header region is required by the PCI 2.2 specification. These registers must be implemented. The
capabilities registers are optional; however, they must adhere to section 6.7 of the PCI SIIG 2.2 specification.
Each capability has a unique ID, which is well-defined. The capabilities are chained using the Next Caps field,
in the capability register. The last capability will have a Next Caps field, which is zeroed.

The Device-Specific registers are shown in

.

Indirect Mode

Host software may use Indirect mode to access the Ethernet controller resources, without using Memory
Mapped I/O. Indirect mode shadows MAC resources to PCI configuration space registers. These shadow
registers can be read/written by system software through PCI configuration space registers. The Ethernet
controller Indirect mode registers expose the following MAC resources:

• Registers
• Local Memory
• Mailboxes

Indirect mode access can be used in conjunction with Standard mode PCI access. Indirect mode has no
interdependency on other PCI access modes and is a mode in itself.

Table 47: Device Specific Registers

Register

Cross Reference

Miscellaneous Host Control

“Miscellaneous Host Control Register (offset: 0x68)” on page 282

PCI State

“PCI State Register (offset: 0x70)” on page 285

Register Base Address

“Register Base Register (offset: 0x78)” on page 286

Memory Base Address

“Memory Base Register (offset: 0x7C)” on page 286

.

Register Data

“Register Data Register (offset: 0x80)” on page 286

.

Memory Window Data

“Memory Data Register (offset: 0x84)” on page 287

.

UNDI Receive BD Standard Producer

Ring Producer Index Mailbox

“UNDI Receive BD Standard Producer Ring Producer Index Mailbox

Register (offset: 0x98–0x9C)” on page 287

UNDI Receive Return Ring Consumer

Index Mailbox

“UNDI Receive Return Ring Consumer Index Register (offset: 0x88–

0x8C)” on page 287

.

UNDI Send BD Producer Index Mailbox

“UNDI Send BD Producer Index Mailbox Register (offset: 0x90–

0x94)” on page 287

Note:

Host software must assert the Indirect_Mode_Access bit in the Miscellaneous Host Control

register (see

“Miscellaneous Host Control Register (offset: 0x68)” on page 282

) to enable indirect

mode.

«
...
170
171
172
173
174
...
»

Summary of Contents for NetXtreme/NetLink BCM5717


















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NetXtreme/NetLink BCM5717

Brand: ZKTeco Pages: 123

Brand: HANYOUNG NUX Pages: 56

Brand: L. G. B. Pages: 2

Brand: L-Acoustics Pages: 36

Brand: Objective Imaging Pages: 11

Brand: Atmel Pages: 12

Brand: Wilo Pages: 128

Brand: HANYOUNG NUX Pages: 4

Brand: Gain Electronic Pages: 17

Brand: Vexve Pages: 24

Brand: CAME Pages: 40

Brand: Interroll Pages: 54

Brand: Daikin Pages: 18

Brand: MOB Pages: 5

Driver VISIO IoT

Brand: Sulion Pages: 8

Brand: Sentiotec Pages: 92

Brand: Waves Pages: 30

Brand: CoolGear Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands