Broadcom NetXtreme/NetLink BCM5717 Programmer'S Manual Download Page 469

Page: 469 / 593

GRC Registers

BCM5718 Programmer’s Guide

Broadcom

January 29, 2016 • 5718-PG108-R

Page 469

Interrupt on RX RISC Attention 25

Cause a host interrupt when an enabled RX-

RISC attention occurs.

TXCP_ATTN_INT_EN

TXCP attention bit.

Receive No Pseudo-header

checksum

Do not include the pseudo-header in the TCP or

UDP checksum calculations. To obtain the

correct checksum, the driver must add the TCP/

UDP checksum field to the pseudo-header

checksum.

Pcie TL/DL/PL mapping bit

–

NVRAM Write Enable

The host must set this bit before attempting to

update the Flash or SEEPROM

Note:

This bit is only valid when set from GRC

port 0. Setting/clearing of this bit from GRC port

1 does not affect NVRAM write access control.

For BCM5718 family, it is recommended to use

0x7024[1] from all ports to control NVRAM write

access.

Send No Pseudo-header

checksum

Do not include the pseudo-header in the TCP or

UDP checksum calculations. To obtain the

correct checksum, the driver must seed the TCP/

UDP checksum field with the pseudo-header

checksum.

Time Sync Mode Enable

Write 1 to this bit to enable Time Sync Mode.

HTX2B Feature Enable

(BCM5720)

Write 1 to enable TX-MAC to route HTX2B

packets to the APE. Firmware may enable/

disable this in flight with careful coordination.

Host Send BDs

Use host-based BD rings instead of NIC-based

BD rings.

Host Stack Up

The host stack is ready to receive data from the

NIC.

B2HRX Feature Enable

Write 1 to enable DMA Engine to route B2HRX

packets to PCIe. Firmware may enable/disable

this in flight with careful coordination.

Don't Interrupt on Receives

Never cause an interrupt on receive return ring

producer updates.

Don't Interrupt on Sends

Never cause an interrupt on send BD ring

producer updates.

DW_SYS_ATTN

WDMA attention bit.

Allow Bad Frames

The RX MAC forwards illegal frames to the NIC

and marks them as such instead of discarding

them. The frames are queued based on default

class and interrupt distribution queue number.

NO_CRC

–

Name

Bits

Access

Default
Value

Description

Summary of Contents for NetXtreme/NetLink BCM5717


















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for NetXtreme/NetLink BCM5717

Reviews:

Related manuals for NetXtreme/NetLink BCM5717

Brands by name

Popular brands

Broadcom NetXtreme/NetLink BCM5717, Programmer'S Manual

Search results

Summary of Contents for NetXtreme/NetLink BCM5717

Reviews:

Related manuals for NetXtreme/NetLink BCM5717

Brands by name

Popular brands