Broadcom NetXtreme/NetLink BCM5717 Programmer'S Manual Download Page 86

Page: 86 / 593

Status Block

BCM5718 Programmer’s Guide

Broadcom

January 29, 2016 • 5718-PG108-R

Page 86

• Bit [0]: Update bit
• Bit [31:1]: Reserved 0x0

Status Block and INT MailBox Addresses

Each status block may be placed in an independent host memory address (64-bit). Each vector may be
acknowledged via associated INT MailBoxes.

The Status word field contains bit flags that contain error information about the status of the controller. The
defined flags are listed in

Table 19

Table 18: Status Block Host Addresses and INT MailBox Addresses

Status
Block #

Status Block Host
Address Register
(64-Bit)

RSS Mode

Comments

INT MailBox
Register
Address

Indication
Items

Legacy

0x3C3C, 0x3C38

0x200

All

Legacy status block
Used by INTx or MSI

x3C3C, 0x3C38

0x200

Link-Status change
Error/Attention
SBD Ring 1 Cons Index
Std RBD Cons Index
Jmb RBD Cons Index

Used in all MSI-X modes for

Vector#0

0x3D00, 0x3D04

0x208

Rx Return Ring 0
Prod Index

Used only in MSI-X multivector

RSS mode or multivector EAV

mode for Vector#1–Vector#4

0x3D08, 0x3D0C

0x210

Rx Return Ring 1
Prod Index

0x3D10, 0x3D14

0x218

Rx Return Ring 2
Prod Index

0x3D18, 0x3D1C

0x220

Rx Return Ring 3
Prod Index

0x3D20, 0x3D24

N/A

Used only in MSI-X multivector

EAV mode for Vector#5

Table 19: Status Word Flags

Bits

Name

Description

Updated

This bit is always set to 1 each time the status block is updated in the host via

DMA. It is expected that host software clear this bit in the status block each time

it examines the status block. This provides the host driver with a mechanism to

determine whether the status block has been updated since the last time the

driver looked at the status block.

Summary of Contents for NetXtreme/NetLink BCM5717


















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for NetXtreme/NetLink BCM5717

Reviews:

Related manuals for NetXtreme/NetLink BCM5717

Brands by name

Popular brands

Broadcom NetXtreme/NetLink BCM5717, Programmer'S Manual

Search results

Summary of Contents for NetXtreme/NetLink BCM5717

Reviews:

Related manuals for NetXtreme/NetLink BCM5717

Brands by name

Popular brands